Register Now

dxtarl · 11-19-2008, 04:58 PM

Thanks The Bum

uluaz · 12-11-2008, 10:32 PM

Quote:

Originally Posted by dhoff002

Will the futaba 3151 work okay with the multigov pro as a throttle servo on my new trex 600n?

Or should I invest in a better servo?

Thanks,

Dan

My friend and I both used futaba 3151's and they both eventually went dead in a few months. I recommend some other servo like a 9252 or 9452.

Lapplandicranger · 12-15-2008, 05:19 AM

A question about the limiter function. Yesterday I went flying for the first time with the MGP installed. I use gov OFF for normal, 1800/std for Idle 1 and 2000/std for Idle 2.

The thing is that I have about 2300 rpm in normal mode. My throttle curve was 10-50-70.
Lowered it today to 10-30-50. But I still want to use the limiter function in case thats not enough..

Regarding setup, from what I understand I should set the 3D limiter to on, then set the normal mode to 3D and RPM 1800 to set the limit to 1800. Then it will not hunt for 1800 just limit when I reach that RPM.

Is that right?

Laurens · 12-25-2008, 04:44 PM

I'm downloading the vids now. I'm seriously considering this governor for my BW Stratus.

sonofcar · 12-25-2008, 06:30 PM

Quote:

Originally Posted by Laurens

I'm downloading the vids now. I'm seriously considering this governor for my BW Stratus.

dude you will like it, easy set up and works flawless

kickybanks · 12-29-2008, 12:36 PM

I just installed new bearings in my os50 and installed the mgp at the same time should I just break it in while flying normal mode and set the mgp below 500 to leave it off in normal? If so what kind of curve should I run it at ?

Laurens · 12-29-2008, 05:20 PM

If you only replaced the bearings you don't need to run it in again. If you changed your ring/liner its a good idea to run in the engine again.

kickybanks · 12-30-2008, 10:09 AM

If I knew that I would have been flying it already instead of waiting for the nice weather. I've had a day or two that I could have flown but waited because I would have been just breaking it in . Thanks for the info

FlyingHigh 450 · 01-01-2009, 10:56 PM

Im saving my money for one of these for sure.Im a noob so I have to be sure,this is a gov and carbsmart in one right?

Pinecone · 01-02-2009, 04:40 AM

Yes. And the gov can also be run as a limiter, but the gov is so good you won't want to.

sonofcar · 01-10-2009, 02:43 AM

Quote:

Originally Posted by Pinecone

Yes. And the gov can also be run as a limiter, but the gov is so good you won't want to.

run limiter mode and a flat 100% curve and you will really like it, compared to gov mode i like limiter better.

wowowee · 01-17-2009, 11:16 AM

just got my aerospire mutligov pro from helidirect..installed in my trex6..followed this vid.made the install and understanding very easy to a T.. thanks Bob...

i notice after programming that is is a Version 1.0.. also Bob's is ver.1.0
some reseach there is a ver.2.0 http://aerospire.com/support_multigov-update.html
just wonderin' if i should send it back.. any1 done this ? :o

Pinecone · 01-17-2009, 04:11 PM

Version 2. 0 applies to the older MultiGov, not the MultiGov Pro.

As I understand it, the MultiGov 2.0 and MultiGov Pro are very similar in governor functions and operation. The MultiGov Pro adds the mixture control capability.

wowowee · 01-17-2009, 06:53 PM

oh i c
thanks pinecone..

kickybanks · 01-22-2009, 11:48 AM

Can anyone shed some light on this for me ? I made up the temp sensor just like bob and checked it and it worked fine then ordered artic silver . after three days I went to install sensor and when I did the display says it is not connected. I havent even used it and lost a sensor, what could have happend to it ? anyone else had this happen or am I doing something wrong?

dxtarl · 01-22-2009, 08:53 PM

Quote:

Originally Posted by kickybanks

Can anyone shed some light on this for me ? I made up the temp sensor just like bob and checked it and it worked fine then ordered artic silver . after three days I went to install sensor and when I did the display says it is not connected. I havent even used it and lost a sensor, what could have happend to it ? anyone else had this happen or am I doing something wrong?

Is Artic Silver conductive?

TheBum · 01-22-2009, 09:36 PM

Quote:

Originally Posted by dxtarl

Is Artic Silver conductive?

Yes, but I think kicky was saying that he hadn't even applied any; he had done nothing other than hook it up again.

If that's not the case, my sensor failed between the time I put Arctic Alumina (not Silver; Alumina is non-conductive) and when I applied it to the head. I never did try again, but when I do, I will be using the new sensor with the thermistor on a circuit board.

Pinecone · 01-23-2009, 09:37 AM

There is a reason they give you multiple sensors.

kickybanks · 01-23-2009, 10:13 AM

I took off the heat shrink last night and sure enough the sensor was cracked right down the middle so I built another one and checked it and it said the room temp was 22c and then installed with artic silver and rtv for stabilty and checked the temp again. It now says it is 6c, can this be right because the heli is stored in the same room that is 22c . All that changed is I installed it and the temp went way down.

kickybanks · 01-23-2009, 10:17 AM

when I made this sensor I also used so shoe goop between the two wires but not on the thermistor or even close to it. I hope this will give it more of a fighting chance and hold together better then the last one

12-15-2008, 05:19 AM	#43 (permalink)
Lapplandicranger Registered Users My HF Map location Join Date: Jul 2008	A question about the limiter function. Yesterday I went flying for the first time with the MGP installed. I use gov OFF for normal, 1800/std for Idle 1 and 2000/std for Idle 2. The thing is that I have about 2300 rpm in normal mode. My throttle curve was 10-50-70. Lowered it today to 10-30-50. But I still want to use the limiter function in case thats not enough.. Regarding setup, from what I understand I should set the 3D limiter to on, then set the normal mode to 3D and RPM 1800 to set the limit to 1800. Then it will not hunt for 1800 just limit when I reach that RPM. Is that right? __________________ T-rex 600N SuperPro, OS50 Hyper, Align DS610s, MultiGovPro with Hitec HS-5065MG, Logictech 6100T+6100G, Spektrum DX7.

12-25-2008, 04:44 PM	#44 (permalink)
Laurens Registered Users My HF Map location Join Date: Apr 2004	I'm downloading the vids now. I'm seriously considering this governor for my BW Stratus. __________________ Logo 800/Jeti DS16

12-29-2008, 12:36 PM	#46 (permalink)
kickybanks Registered Users My HF Map location Join Date: Dec 2007	should I disable my mgp when doing break in? I just installed new bearings in my os50 and installed the mgp at the same time should I just break it in while flying normal mode and set the mgp below 500 to leave it off in normal? If so what kind of curve should I run it at ?

12-29-2008, 05:20 PM	#47 (permalink)
Laurens Registered Users My HF Map location Join Date: Apr 2004	If you only replaced the bearings you don't need to run it in again. If you changed your ring/liner its a good idea to run in the engine again. __________________ Logo 800/Jeti DS16

12-30-2008, 10:09 AM	#48 (permalink)
kickybanks Registered Users My HF Map location Join Date: Dec 2007	wow If I knew that I would have been flying it already instead of waiting for the nice weather. I've had a day or two that I could have flown but waited because I would have been just breaking it in . Thanks for the info

11-19-2008, 04:58 PM	#41 (permalink)
dxtarl Registered Users My HF Map location Join Date: Jul 2006	Thanks The Bum

01-02-2009, 04:40 AM	#50 (permalink)
Pinecone Registered Users Join Date: Sep 2006	Yes. And the gov can also be run as a limiter, but the gov is so good you won't want to. __________________ Terry AMA#47402, IRCHA # 3395 Blade CP "Pro", Trex 450SE, PiccoZ, Quick of Japan EP8v2 EX, Hurricane 550, Hurricane 200, JR Vibe 50, Blade mCX, Bergen Intrepid Gasser, Pantera 50, Blade mSR, Novus CP

01-17-2009, 11:16 AM	#52 (permalink)
wowowee Registered Users Join Date: Jan 2009	just got my aerospire mutligov pro from helidirect..installed in my trex6..followed this vid.made the install and understanding very easy to a T.. thanks Bob... i notice after programming that is is a Version 1.0.. also Bob's is ver.1.0 some reseach there is a ver.2.0 http://aerospire.com/support_multigov-update.html just wonderin' if i should send it back.. any1 done this ? :o

01-17-2009, 04:11 PM	#53 (permalink)
Pinecone Registered Users Join Date: Sep 2006	Version 2. 0 applies to the older MultiGov, not the MultiGov Pro. As I understand it, the MultiGov 2.0 and MultiGov Pro are very similar in governor functions and operation. The MultiGov Pro adds the mixture control capability. __________________ Terry AMA#47402, IRCHA # 3395 Blade CP "Pro", Trex 450SE, PiccoZ, Quick of Japan EP8v2 EX, Hurricane 550, Hurricane 200, JR Vibe 50, Blade mCX, Bergen Intrepid Gasser, Pantera 50, Blade mSR, Novus CP

01-17-2009, 06:53 PM	#54 (permalink)
wowowee Registered Users Join Date: Jan 2009	oh i c thanks pinecone..

01-22-2009, 11:48 AM	#55 (permalink)
kickybanks Registered Users My HF Map location Join Date: Dec 2007	sensor not connected Can anyone shed some light on this for me ? I made up the temp sensor just like bob and checked it and it worked fine then ordered artic silver . after three days I went to install sensor and when I did the display says it is not connected. I havent even used it and lost a sensor, what could have happend to it ? anyone else had this happen or am I doing something wrong?

01-23-2009, 09:37 AM	#58 (permalink)
Pinecone Registered Users Join Date: Sep 2006	There is a reason they give you multiple sensors. __________________ Terry AMA#47402, IRCHA # 3395 Blade CP "Pro", Trex 450SE, PiccoZ, Quick of Japan EP8v2 EX, Hurricane 550, Hurricane 200, JR Vibe 50, Blade mCX, Bergen Intrepid Gasser, Pantera 50, Blade mSR, Novus CP

01-23-2009, 10:13 AM	#59 (permalink)
kickybanks Registered Users My HF Map location Join Date: Dec 2007	I took off the heat shrink last night and sure enough the sensor was cracked right down the middle so I built another one and checked it and it said the room temp was 22c and then installed with artic silver and rtv for stabilty and checked the temp again. It now says it is 6c, can this be right because the heli is stored in the same room that is 22c . All that changed is I installed it and the temp went way down.

01-23-2009, 10:17 AM	#60 (permalink)
kickybanks Registered Users My HF Map location Join Date: Dec 2007	when I made this sensor I also used so shoe goop between the two wires but not on the thermistor or even close to it. I hope this will give it more of a fighting chance and hold together better then the last one

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in