How do you polarize a single magnet?

foolforspeed · 03-01-2012, 01:27 PM

The total G gov senser comes with one magnet and the instructions say to polarize it. How do you do that without going through the whole setup process? I want to install the sensor and magnet before the servos so I can get to the clutch bell. I have the align gov on my 600 which is 2 mags put in opposit each other so its a no brainer (especially with Bobs videos). Thanks for any help you can give me.

vboy55 · 03-01-2012, 04:50 PM

You can bind the total g or hook to a receiver and just plug the sensor into the unit and go to the software and check it

http://curtisyoungblood.com//TotalGS...tions%20V2.pdf

Page 7

Tommy

Sent from my iPhone using Tapatalk

foolforspeed · 03-02-2012, 09:22 PM

Thanks for the info but I wanted to install the sensor and mag before I installed the electronics because its easier to get to. I'm gonna try to mount the sensor with the mag just setting in place and see if I can get to the mag for a later epoxy install. Its gonna be tight but I might be able to pull it off.

mystar60 · 03-02-2012, 11:03 PM

What I will do is using the GView2 power up the Total G with just the sensor plugged in and then scroll to the Governor at/not at sensor to verify the magnet polarity. You can do the same with the interface software.
This should help with your build.

foolforspeed · 03-03-2012, 10:57 AM

Now that's a good idea. Thanks for the input.

03-01-2012, 01:27 PM	#1
foolforspeed Registered Users Join Date: Aug 2010 Location: San Antonio	How do you polarize a single magnet? The total G gov senser comes with one magnet and the instructions say to polarize it. How do you do that without going through the whole setup process? I want to install the sensor and magnet before the servos so I can get to the clutch bell. I have the align gov on my 600 which is 2 mags put in opposit each other so its a no brainer (especially with Bobs videos). Thanks for any help you can give me.

03-02-2012, 11:03 PM	#4
mystar60 Registered Users My HF Map location Join Date: Aug 2004 Location: Clifton, NJ	What I will do is using the GView2 power up the Total G with just the sensor plugged in and then scroll to the Governor at/not at sensor to verify the magnet polarity. You can do the same with the interface software. This should help with your build. __________________ CYE Field rep http://curtisyoungblood.com/ Ballistic 700,Ballistic 635, Rave ENV Nitro, Rave 450, TotalG, MP7, Radix Blades

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-01-2012, 04:50 PM	#2
vboy55 Registered Users My HF Map location Join Date: Jan 2008 Location: Ft. Pierce	You can bind the total g or hook to a receiver and just plug the sensor into the unit and go to the software and check it http://curtisyoungblood.com//TotalGS...tions%20V2.pdf Page 7 Tommy Sent from my iPhone using Tapatalk

03-02-2012, 09:22 PM	#3
foolforspeed Registered Users Thread Starter Join Date: Aug 2010 Location: San Antonio	Thanks for the info but I wanted to install the sensor and mag before I installed the electronics because its easier to get to. I'm gonna try to mount the sensor with the mag just setting in place and see if I can get to the mag for a later epoxy install. Its gonna be tight but I might be able to pull it off.

03-03-2012, 10:57 AM	#5
foolforspeed Registered Users Thread Starter Join Date: Aug 2010 Location: San Antonio	Now that's a good idea. Thanks for the input.