Honey Bee cp3 Tail got superspeed

[killernilsen]

Originally Posted by 755 robert

Your heli looks to be the same head setup as the blade cp.The swash should move up for neg pitch and the swash should move down for positive pitch..

Yea it is supose to do that!
but it dosent
this is what happens when the arms are correct and moving in sync

Trottle up = Negativ pitch and the swash plate travels upp
Trottle down = posetive pitch and the swash plate travels down
to make this correct i have to reverse Thr. and start from bottom but that makes it full trottle at startupp. and that wold be a bad bad idea.
but how to we change the swash plate to go the other way whit a standard E-sky Transmitter 6ch from a belt cp v2

[praetorious]

Ah, I think I know what it is. You've got your servos are in the wrong ports. Use the switch settings I told you, and put the servos as follows:
1-aileron
2-elevator
6-pitch
B.R.
Amit

[killernilsen]

Originally Posted by praetorious

Ah, I think I know what it is. You've got your servos are in the wrong ports. Use the switch settings I told you, and put the servos as follows:
1-aileron
2-elevator
6-pitch
B.R.
Amit

nope that only gives us a new problem
then the elevator is moved to Trottle and Pitch in elevator and they dont move in sync
so that gives me result in when i am throttling up my heli tilt back wards. and when i move the elevator stick forward (supose to tilt forward) it gives me posetive pitch and when i move the elevator stick backwards (supose to tilt backwards) it gives me negativ pitch, and the servos are not moving in sync.

[praetorious]

Man this is weird, I got those settings straight from the manual, unless i have a different manual. Can you take a close up pic of your 3-in-1 for me? Also A shot with t he cabling to each servo would be nice too.

B.R.
Amit

[Rotteknekten]

Hi This is our receiver setup :
1-pitch
2-ele
6-ail

[praetorious]

Any progress? I've not abandoned you. Just very busy and will be for the next two weeks. I take it your machine is the one on the right side of the page. I can't quite make out the channel assignments, but It looks like it should be:
1-AIL
2-ELE
3- THR
4-RUD
5-GAIN
6-Pitch

Which are the assignments I had posted but you said they didn't work

Are your cables from the 3 in 1 in the the right channels?
Try the manuals setup and fool with the reversing switches perhaps.
If that doesn't work, I would say to go back to the assignments that you had in your video and just mess around with the reversing switch.
I can't tell from your photos which servos are in which port, don't take it the wrong way, just need to make sure that what's the elevator servo is the elevator servo and so forth.

This is very odd, because the manual should be correct, and the channel assignments are pretty standard.

B.R.
Amit

[killernilsen]

Hello and thanks for the answers we aculy found out the problem. the belt cp v2 use the pitch uppward, but the Honey bee`s goes down . and we did use the belt controle so we had to flip the whole head so we get posetiv pitch uppwards witch is manual revers of the swash mitch. the wole problem was becuse of the controles that we did use. belt and honey bee controles are difrent the swash mix gose difrent ways.
but thanks agian for helping out now thy fly like a propper bee whit flipped head hehe.

[praetorious]

Ahhh, that's interesting. Good that you've got it working now. Flipping the grips was another way to go.
Have you also tried using a sim? It will save a lot of money as you're learning. You can try Heli-X, it's free. Once you can hover in the sim, grab your training gear and RADD's and start flying.

B.R.
Amit