Fun, Learning, Friendship and Mutual Respect
START  HERE


Unregistered
Go Back   HeliFreak > R/C Helicopter Support > Walkera Helicopters


Walkera Helicopters Walkera Helicopter Support


Reply
 
Thread Tools Display Modes
Old 08-10-2012, 12:54 PM   #41
indiggio
Registered Users
 

Join Date: Mar 2012
Location: USA
Default

Quote:
Originally Posted by CX2Pilot View Post
Go into the following menu and set to these settings.

MODEL - OUTPU

AUX2
AUX2

AUX2
GYRO


FUNCTION - GYRO

MODE- MANU

SWITC - FMD

POS 0
34.0% = 6 axis mode - Red light on Ladybird

POS 1
66.0% = 3 axis mode - Green light on Ladybird

_____________________________


DREXP

Pos 0: ELEV D/R - 80% EXP +30% > You can use much less D/R and more Expo if you need to.
Pos 0: AILE D/R - 80%, EXP +30%
Pos 0: RUDD D/R - 100% EXP LIN

Pos 1: ELEV D/R - 100% EXP +30%
Pos 1: AILE D/R - 100%, EXP +30%
Pos 1: RUDD D/R - 100%, EXP LIN

If you want more agressive 3D mode try these settings.

Pos 1: ELEV D/R - 110% % EXP LIN
Pos 1: AILE D/R - 110%, EXP LIN
Pos 1: RUDD D/R - 120%, EXP -20 % > You can even try 150% for RUDD and more negitave EXP for fast rudder response.
I just received my Ladybird and am trying to configure up my Devo 10 using your instructions, but I'm a bit confused by some of them. Hoping you can help with a bit of clarification? Most of the settings I get, thanks so much for them!
A couple just don't compute.

I want to use the FMOD switch to switch between flight modes. I see that seems to work as LED on Ladybird changes with switch.

What doesn't make sense to me is this part:

MODEL - OUTPU

AUX2
AUX2

AUX2
GYRO


FUNCTION - GYRO

MODE- MANU

SWITC - FMD

I can't seem to match it to the Devo 10 menu system. If you could clarify that a bit, that would be super!


Another question I have is with the DR/EXP setup.
For Pos 0 & Pos 1, do you actually flip the corresponding switches on the Devo 10 associated with the function (ELEV D/R, AILE D/R, RUDD D/R) or are those different Pos settings somehow tied to the FMOD switch, so that the DR/EXP settings switch based on the FMOD switch and not each of the function switches?
I typically use the AILE D/R switch as my throttle hold (I keep my middle finger resting on it ready to flip it whenever necessary).


One more. Do the AUX4 and AUX5 dials actually do anything with the LB?

Thanks!
__________________
Genius CP, New V120D02S, LadyBird QR
Devo 10
Phoenix
indiggio is offline        Reply With Quote
Old 08-29-2012, 09:26 AM   #42
boxhead
Registered Users
 

Join Date: Mar 2012
Location: Chico
Default Hoten x

I found CX2's setup for the ladybird qr worked very good, mine came with devo7 with a major problem in when I flipped the fmod inthe ladybird would go to full throttle!
I got it set right, but being slow( ok dumb) I kept missing fmod switch doing anything but changing led on FC. Then read your guide, and understanding my devo7 came from YOUR instructions.
Thanks.
I got ( finially ) the hotenX, BNF. And used your ladybirdQR as starting point!

What I don't get, is why would brushled FC settings on tx work on with Brushless FC ?
I know the tx isn't caring what it's controlling, the FC just wants to either stablalize with 3 or 6 axis, Im not putting the words right to say what i mean. It's not like I would use these settings on my x650, other than have similar yaw/rudder expo in positive and ele/ale expo in negative,
boxhead is offline        Reply With Quote
Old 09-01-2012, 10:45 AM   #43
CX2Pilot
Forum Support
 
Posts: 693
Thread Starter Thread Starter
 

Join Date: Jun 2008
Location: Cleveland, Ohio
Default

Quote:
Originally Posted by ohioshooter View Post
Hi, Do any of you have the full settings for 2801 and cb100 double brushless that has the RX2436.

Thanks

You should be able to use my CB100 setup guide with the RX2406 for the RX2436.
Create a new model or reset a current one.
Use the settings I listed. All the other settings are at there default settings.
This is why I didn't make a full setup guide as you only need to change
a few settings from the defaults.

For DR/EXPO you can try these settings.


DR&EXP:


Set D/R and EXPO to your personal needs/preference.
These should be good for beginners.
You can set more or less than 70% D/R if you want and more
or less than +30% EXPO if you want.


ELEV D/R - 70% EXP +30%

AILE D/R - 70%, EXP +30%

RUDD D/R - 100%, EXP LIN *



Tom
__________________
Moderator for the Blade and Walkera Forums.
Walkera V100D01 V2 DBL, Walkera 4G6 w/RX2610V2, Align T-Rex 450SE V2, Blade mCPX V1 BL, Walkera Mini CP BL, Walkera QR Ladybird, Walkera Hoten X, Walkera Master CP.
CX2Pilot is offline        Reply With Quote
Old 09-01-2012, 11:01 AM   #44
CX2Pilot
Forum Support
 
Posts: 693
Thread Starter Thread Starter
 

Join Date: Jun 2008
Location: Cleveland, Ohio
Default

Quote:
Originally Posted by rldeveer View Post
Tom
I have found your beginner and other guides very usefull and am about to move up to BL. I don't see a guide for a C05 BL GCP w/ 2801.
Can your #16 setup guide for MiniCP with "C05 BL" be used for my 2801 Genius that
has been converted to a Mini?
Would the 50% TC still = 90% throttle on the 2801/WK GCP or was that specific to the Devo/Mini?
What would you suggest using for pot settings on the GCP WK RX for this setup.

Thanks,
RD
??????Where did he go?????

RD,

I'm glad my setup guides were able to help you out.

Q: Can your #16 setup guide for MiniCP with "C05 BL" be used for my 2801 Genius that has
been converted to a Mini?

A: Yes. The setup guides are the same for the Genius CP and Mini CP both brush
and brushless. I listed them separate so I can find tune and tweek them if needed.
I used one setup guide for the GCP and MCP both brush and brushless.

Q: What would you suggest using for pot settings on the GCP WK RX for this setup.
A: I used the factory defaults which worked well for me. On the GCP I turned up the servo ext.


Q: ??????Where did he go?????[/QUOTE]
A: I don't go on the forums much anymore...


Tom
__________________
Moderator for the Blade and Walkera Forums.
Walkera V100D01 V2 DBL, Walkera 4G6 w/RX2610V2, Align T-Rex 450SE V2, Blade mCPX V1 BL, Walkera Mini CP BL, Walkera QR Ladybird, Walkera Hoten X, Walkera Master CP.
CX2Pilot is offline        Reply With Quote
Old 09-01-2012, 11:19 AM   #45
CX2Pilot
Forum Support
 
Posts: 693
Thread Starter Thread Starter
 

Join Date: Jun 2008
Location: Cleveland, Ohio
Default

Quote:
Originally Posted by indiggio View Post
I just received my Ladybird and am trying to configure up my Devo 10 using your instructions, but I'm a bit confused by some of them. Hoping you can help with a bit of clarification? Most of the settings I get, thanks so much for them!
A couple just don't compute.

I want to use the FMOD switch to switch between flight modes. I see that seems to work as LED on Ladybird changes with switch.

What doesn't make sense to me is this part:

MODEL - OUTPU

AUX2
AUX2

AUX2
GYRO


FUNCTION - GYRO

MODE- MANU

SWITC - FMD

I can't seem to match it to the Devo 10 menu system. If you could clarify that a bit, that would be super!


Another question I have is with the DR/EXP setup.
For Pos 0 & Pos 1, do you actually flip the corresponding switches on the Devo 10 associated with the function (ELEV D/R, AILE D/R, RUDD D/R) or are those different Pos settings somehow tied to the FMOD switch, so that the DR/EXP settings switch based on the FMOD switch and not each of the function switches?
I typically use the AILE D/R switch as my throttle hold (I keep my middle finger resting on it ready to flip it whenever necessary).


One more. Do the AUX4 and AUX5 dials actually do anything with the LB?

Thanks!



Q: What doesn't make sense to me is this part:

MODEL - OUTPU

AUX2
AUX2

AUX2
GYRO


FUNCTION - GYRO

MODE- MANU

SWITC - FMD

I can't seem to match it to the Devo 10 menu system. If you could clarify that a bit, that would be super!


A: Those settings are for the Devo 7 which will be different on the Devo 10.
I would post this question in my Ladybird review and someone who has the Devo 10 should
be able to help you out.

http://helifreak.com/showthread.php?t=406988


Q: Another question I have is with the DR/EXP setup.
For Pos 0 & Pos 1, do you actually flip the corresponding switches on the Devo 10 associated with the function (ELEV D/R, AILE D/R, RUDD D/R) or are those different Pos settings somehow tied to the FMOD switch, so that the DR/EXP settings switch based on the FMOD switch and not each of the function switches?
I typically use the AILE D/R switch as my throttle hold (I keep my middle finger resting on it ready to flip it whenever necessary).

A: There are different methods for assigning DR/EXP. Using the switches, auto mode
tied to the FMOD switch. If you going to use AILE D/R switch as your throttle hold
then you going to need to assign the FMOD switch to also contro; DR/EXPO.
I don't have the Devo 10 so I can't tell you how to do this.


Q: One more. Do the AUX4 and AUX5 dials actually do anything with the LB?
A: One is for firmware updates and one is for camera DC wire or lights (LED).


Tom
__________________
Moderator for the Blade and Walkera Forums.
Walkera V100D01 V2 DBL, Walkera 4G6 w/RX2610V2, Align T-Rex 450SE V2, Blade mCPX V1 BL, Walkera Mini CP BL, Walkera QR Ladybird, Walkera Hoten X, Walkera Master CP.
CX2Pilot is offline        Reply With Quote
Old 09-01-2012, 04:32 PM   #46
rldeveer
Registered Users
 

Join Date: Nov 2011
Location: Big Island of Hawaii
Default

Quote:
Originally Posted by CX2Pilot View Post
RD,

I'm glad my setup guides were able to help you out.

Q: Can your #16 setup guide for MiniCP with "C05 BL" be used for my 2801 Genius that has been converted to a Mini?

A: Yes. The setup guides are the same for the Genius CP and Mini CP both brush
and brushless. I listed them separate so I can find tune and tweek them if needed.
I used one setup guide for the GCP and MCP both brush and brushless.

Q: What would you suggest using for pot settings on the GCP WK RX for this setup.
A: I used the factory defaults which worked well for me. On the GCP I turned up the servo ext.


Tom
Tom
Thanks for the response.
The ST1 50% flat TC = 90% throttle doesn't make sence to me but does give a nice very melow flight. I think it is well below 90% on my 2801/MGCP BL.

I use your #21 indoors, and am proggessing from #24 to #15 and then #16 in due time.
My biggest problem is still nose in. I can sit in one place all day long in all other orientations, but lose it as soon as the nose comes around. Dumb Thumbs.
Regards
RD
rldeveer is offline        Reply With Quote
Old 09-01-2012, 05:50 PM   #47
CX2Pilot
Forum Support
 
Posts: 693
Thread Starter Thread Starter
 

Join Date: Jun 2008
Location: Cleveland, Ohio
Default

Your welcome RD.

The ST1 50% flat TC = 90% throttle we think has to do with how the throttle programming is
done in the 3 axis RX firmware.
On the Walkera non 3 axis RX I have found that 90% TX throttle gives you 90% actual motor throttle.

On the Blade mCPX which has the 3 axis RX I found this out.

With the thesteve mCPX version I had to set the TX throttle to 20% across to get 85% actual motor throttle
in ST-1 for indoor flying.
Connected the yellow wire to the main motor output pin on the 3in1.

With the regular thesteve when I set the TX throttle to 80% across I got 85% actual motor throttle.
Soldered the yellow wire to the back of the 3in1 on the tiny resistor.


Nose in tricky. It is the hardest for me to do also.


Tom
__________________
Moderator for the Blade and Walkera Forums.
Walkera V100D01 V2 DBL, Walkera 4G6 w/RX2610V2, Align T-Rex 450SE V2, Blade mCPX V1 BL, Walkera Mini CP BL, Walkera QR Ladybird, Walkera Hoten X, Walkera Master CP.

Last edited by CX2Pilot; 09-01-2012 at 11:45 PM..
CX2Pilot is offline        Reply With Quote
Old 09-04-2012, 11:52 AM   #48
jordan57
Registered Users
 

Join Date: Aug 2012
Location: Prosper
Default Master CP with Devo 10

I just received my first CP heli, a Master CP from RC711.com
Walkera recommended using their downloaded minicp.bin as a starting point for the Master....their settings are very similar.
Once off the ground, the copter spins like there is no rudder control. On second try I applied some opposite rudder, which had no effect. It was all I could do to get it down without injury.
Do you have any ideas of cause. I'm working with the techs at RC711, but would like some real ammunition.
Thanks,
jordan57 is offline        Reply With Quote
Old 09-04-2012, 11:26 PM   #49
CX2Pilot
Forum Support
 
Posts: 693
Thread Starter Thread Starter
 

Join Date: Jun 2008
Location: Cleveland, Ohio
Default

The #1 thing to check is the gyro gain.
If it is too low the tail will not hold and the heli will spin.
Set gyro gain at 82% to start with and adjust more or less as needed.
Also make sure the rudder (RUDD) is set correctly in the TX reverse menu.
It should be set at NORM if it is like the Mini CP.

On the heli you may have a bad tail motor, bad tail motor connection,
stripped teeth on a gear, bad tail blade (bent or cracked) or the tail blade may be slipping on the shaft.
Also the pinion on the tail motor could be slipping.

This is everything I can think of at the moment.


Tom
__________________
Moderator for the Blade and Walkera Forums.
Walkera V100D01 V2 DBL, Walkera 4G6 w/RX2610V2, Align T-Rex 450SE V2, Blade mCPX V1 BL, Walkera Mini CP BL, Walkera QR Ladybird, Walkera Hoten X, Walkera Master CP.
CX2Pilot is offline        Reply With Quote
Old 09-05-2012, 05:54 PM   #50
CX2Pilot
Forum Support
 
Posts: 693
Thread Starter Thread Starter
 

Join Date: Jun 2008
Location: Cleveland, Ohio
Default Setup for the Walkera Master CP

18. How to setup the TX for the Walkera Master CP for the RX2637H-D Receiver - Devo Transmitter.

Walkera recommended using their downloaded minicp.bin as a starting point for the Master.
Their settings are very similar.

You can use the settings here which are from the user manual or you can use my settings for the Mini CP.

http://helifreak.com/showthread.php?t=400204





Devo 6/7/8S/10/12S


Type- Helicopter


SWASH - 1 Servo Normal


STMOD - MODE2 if you want the throttle on the left stick


REVERS - Set all to normal



Device Output

Devo 6


Gear - GEAR SW - GYRO
Pitch - System - Active



Devo 7

Gear - GEAR - ACT
AUX2 - AUX2 - GYRO



Devo 7E

Gear- HOLD SW
Function - Active

AUX2 - FMOD SW
Function - Gyro



Devo 8S

Gear - GEAR SW - Active

Pitch - System - Active

AUX2 - FMOD SW - Gyro

AUX3 - RUDD D/R - Active



Devo 10

Gear - GEAR SW - Active

AUX2 - FMOD SW - Gyro

AUX3 - RUDD D/R - Active

AUX4 - AUX4 KB - Active

AUX5 - AUX5 KB - Active



Devo 12S

Gear - GEAR SW - Active

Pitch - System - Active

AUX2 - AUX2 Lever - Gyro

AUX3 - AUX3 Lever - Active

AUX4 - AUX4 Lever - Active

AUX5 - AUX5 Lever - Active

AUX6 - AUX6 Knob - Active

AUX7 - AUX7 Knob - Active



Gyro Sensor - (Devo 7E)

Mode - Manual

Switch - HOLD SW

Pos 0 = 75.0%

Pos 1 = 50.0%



Gyro Sensor - (Devo 6, Devo 7, Devo 8S, Devo 10, and Devo 12S)

Mode - Manual

Switch - Mix SW

Pos 0 = 75.0%

Pos 1 = 70.0%

Pos 2 = 50.0%



Throttle Curve

Normal Flight

L= 0%

M= 50%

H= 100%


Stunt 1

L= 100%

M= 75%

H= 100%


Stunt 2 - (There is no Stunt 2 for the Devo 7E TX)

L= 100%

M= 75%

H= 100%



Pitch Curve

Normal Flight

L= - 15%

M= + 25%

H= + 55%


Stunt 1

L= - 55%

M= 0%

H= + 55%


Stunt 2 - (There is no Stunt 2 for the Devo 7E TX)

L= - 55%

M= 0%

H= + 55%



-------------------



DR&EXP:

Set D/R and EXPO to your personal needs/preference. These should be good for beginners.
You can set more or less than 70% D/R if you want and more or less than +30% EXPO if you want.


ELEV D/R - 70% EXP +30%

AILE D/R - 70%, EXP +30%

RUDD D/R - 100%, EXP LIN



Tom
__________________
Moderator for the Blade and Walkera Forums.
Walkera V100D01 V2 DBL, Walkera 4G6 w/RX2610V2, Align T-Rex 450SE V2, Blade mCPX V1 BL, Walkera Mini CP BL, Walkera QR Ladybird, Walkera Hoten X, Walkera Master CP.

Last edited by CX2Pilot; 09-11-2012 at 04:34 PM..
CX2Pilot is offline        Reply With Quote
Old 09-07-2012, 01:11 AM   #51
CX2Pilot
Forum Support
 
Posts: 693
Thread Starter Thread Starter
 

Join Date: Jun 2008
Location: Cleveland, Ohio
Default Setup for the Walkera V120D02S

19. How to setup the TX for the RX2622V-D Receiver - Devo Transmitter


Type- Helicopter


SWASH - 1 Servo Normal


STMOD - MODE2 if you want the throttle on the left stick


REVERS - Set all to normal




Device Output


Devo 6


Gear - GEAR SW - GYRO
Pitch - System - Active



Devo 7

Gear - GEAR - ACT
AUX2 - AUX2 - GYRO



Devo 8S

Gear - GEAR SW - Active

Pitch - System - Active

AUX2 - FMOD SW - Gyro

AUX3 - RUDD D/R - Active




Devo 10

Gear - GEAR SW

Function - Active


AUX2 - FMOD SW

Function - Gyro



Devo 12S

Gear - GEAR SW - Active

Pitch - System - Active

AUX2 - AUX2 Lever - Gyro

AUX3 - AUX3 Lever - Active

AUX4 - AUX4 Lever - Active

AUX5 - AUX5 Lever - Active

AUX6 - AUX6 Knob - Active

AUX7 - AUX7 Knob - Active




Gyro Sensor

Mode - Manual

Switch - Mix SW

Pos 0 = 80.0%

Pos 1 = 75.0%

Pos 2 = 50.0%



Throttle Curve

Normal Flight

L= 0%

M= 50%

H= 100%


Stunt 1

L= 100%

M= 75%

H= 100%


Stunt 2

L= 100%

M= 75%

H= 100%



Pitch Curve

Normal Flight

L= - 20%

M= + 20%

H= + 56%


Stunt 1

L= - 56%

M= - 0%

H= + 56%


Stunt 2

L= - 56%

M= - 0%

H= + 56%



-------------------



DR&EXP:

Set D/R and EXPO to your personal needs/preference. These should be good for beginners.
You can set more or less than 70% D/R if you want and more or less than +30% EXPO if you want.


ELEV D/R - 70% EXP +30%

AILE D/R - 70%, EXP +30%

RUDD D/R - 100%, EXP LIN

-
__________________
Moderator for the Blade and Walkera Forums.
Walkera V100D01 V2 DBL, Walkera 4G6 w/RX2610V2, Align T-Rex 450SE V2, Blade mCPX V1 BL, Walkera Mini CP BL, Walkera QR Ladybird, Walkera Hoten X, Walkera Master CP.

Last edited by CX2Pilot; 09-11-2012 at 04:33 PM..
CX2Pilot is offline        Reply With Quote
Old 09-07-2012, 09:20 AM   #52
CX2Pilot
Forum Support
 
Posts: 693
Thread Starter Thread Starter
 

Join Date: Jun 2008
Location: Cleveland, Ohio
Default Setup for the Walkera V120D02S

20. How to setup the TX for the Walkera V120D02S - RX2622-V Receiver - Walkera WK-2801 Pro Transmitter



Step 1. Create a new model (or reset a current model) in the WK-2801 Pro TX.




Step 2. Set to stick mode 2801 if it isn't already set to it. Stay in 2801 stick mode.
*Make sure STICK is set to MODE2* Sometimes it will default to MODE1.

Set the throttle trim all the way down to zero. Default is center.




Step 3. Go into REVERS and set to:

1 2 3 4 5 6 7 8
N N N N N N N N




Step 4. Go into SWASH and set to 1SERVO NORM




Step 5. Go into CURVES THRCURVE and set to:


Norm 0%-25%-50%-75%-100%

ST1 & ST2 - 100%-100%-100%-100%-100%


Another option for ST1 & ST2 if 100% across is too much RPM for your motor is to use these settings.


ST-1 & ST-2 100%-90%-80%-90%-100%


I use this setup. ST-1 is a V Shaped Throttle Curve, ST-2 is 100% across.

ST-1 100%-90%-80%-90%-100%

ST-2 100%-100%-100%-100%-100%




Step 6. Go into CURVES PITCURVE and set to:



Norm 36.5%-41%-50%-65%-80%

ST-1 & ST-2 20%-35%-50%-65%-80%

HOLD 20%-35%-50%-65%-80%




Step 7. Go into GYRHLD, GYROSENS and change INH to GYRO/AUX2

Set to 0: 78%
Set to 1: 78%





Step 8. Go into GYRHLD, THROHOLD, and change INH to THRO HOLD

ACT
HOLD Pos. -15%




Step 9. Go into TRVADJ and set to:

All 100% except Rudder = L120% R120%




Step 10. Go into DR&EXP:

DR&EXP:

Set D/R and EXPO to your personal needs/preference. These should be good for beginners.
You can set more or less than 70% D/R if you want and more or less than +30% EXPO if you want.


ELEV D/R - 70% EXP +30%

AILE D/R - 70%, EXP +30%

RUDD D/R - 100%, EXP LIN


Set AUTO to:

ST-1 ACT

ST-2 ACT

HOLD ACT




Step 11.

Bind Radio and RX.



-
__________________
Moderator for the Blade and Walkera Forums.
Walkera V100D01 V2 DBL, Walkera 4G6 w/RX2610V2, Align T-Rex 450SE V2, Blade mCPX V1 BL, Walkera Mini CP BL, Walkera QR Ladybird, Walkera Hoten X, Walkera Master CP.

Last edited by CX2Pilot; 09-11-2012 at 04:33 PM..
CX2Pilot is offline        Reply With Quote
Old 09-07-2012, 09:25 AM   #53
CX2Pilot
Forum Support
 
Posts: 693
Thread Starter Thread Starter
 

Join Date: Jun 2008
Location: Cleveland, Ohio
Default Setup for the Walkera V120D02

21. How to setup the Walkera V120D02 - RX2610V2 Receiver - Walkera WK-2801 Pro Transmitter



*** First set the RX2610V2 Dip Switches. ***

RX Dip Switch factory positions are both down from the factory.

Set these to the following:

BAL switch down (On) and PIT. REV up (Off).



IMPORTANT!

The PIT and ALIE Servo RX locations will vary between different V120D02 helicopters and different RX2610V's.
Try Option #1 first. If your radio sticks are working correctly you are all set. If not use Option #2.


RX2610V Servo Hookup Option #1


PIT Servo Plug goes into the PIT RX Socket.

ALIE Servo Plug goes into the ALIE RX Socket.

Also see my picture below.



RX2610V Servo Hookup Option #2


PIT Servo Plug goes into the ALIE RX Socket.

ALIE Servo Plug goes into the PIT RX Socket.

Also see my picture below.



*Make sure you verify the settings after you are done before you fly the helicopter.
On the WK-2801 Pro you must hit ENT to save a setting, if you just back out of the menu it will not save the setting.*



**These are settings I have tried and use. These are good starting points for you.
Some people use these settings as they are and others change them to meet there needs.




Step 1. Create a new model (or reset a current model) in the WK-2801 Pro TX.




Step 2. Set to stick mode 2801 if it isn't already set to it. Stay in 2801 stick mode.
*Make sure STICK is set to MODE2* Sometimes it will default to MODE1.

Set the throttle trim all the way down to zero. Default is center.




Step 3. Go into REVERS and set to:

1 2 3 4 5 6 7 8
N N N N N N N N




Step 4. Go into SWASH and set to 1SERVO NORM




Step 5. Go into CURVES THRCURVE and set to:


Norm 0%-25%-50%-75%-100%

ST1 & ST2 - 100%-100%-100%-100%-100%


Another option for ST1 & ST2 if 100% across is too much RPM for your motor is to use these settings.


ST-1 & ST-2 100%-90%-80%-90%-100%


I use this setup. ST-1 is a V Shaped Throttle Curve, ST-2 is 100% across.

ST-1 100%-90%-80%-90%-100%

ST-2 100%-100%-100%-100%-100%




Step 6. Go into CURVES PITCURVE and set to:



Norm 36.5%-41%-50%-65%-80%

ST-1 & ST-2 20%-35%-50%-65%-80%

HOLD 20%-35%-50%-65%-80%




Step 7. Go into GYRHLD, GYROSENS and change INH to GYRO/AUX2

Set to 0: 78%
Set to 1: 78%





Step 8. Go into GYRHLD, THROHOLD, and change INH to THRO HOLD

ACT
HOLD Pos. -15%




Step 9. Go into TRVADJ and set to:

All 100% except Rudder = L120% R120%




Step 10. Go into DR&EXP:

Set D/R and EXPO to your personal needs/preference.
I use 60% D/R and +35% EXPO. I have the Servo EXT on max on the RX.

Set AUTO to:

ST-1 ACT

ST-2 ACT

HOLD ACT




Step 11.

Bind Radio and RX.


-
Attached Thumbnails
Click image for larger version

Name:	DSCF0205_3.jpg
Views:	200
Size:	86.6 KB
ID:	346995   Click image for larger version

Name:	RX2610V Servo Option 1.jpg
Views:	225
Size:	519.8 KB
ID:	346996   Click image for larger version

Name:	RX2610V Servo Option 2.jpg
Views:	170
Size:	519.7 KB
ID:	346997  
__________________
Moderator for the Blade and Walkera Forums.
Walkera V100D01 V2 DBL, Walkera 4G6 w/RX2610V2, Align T-Rex 450SE V2, Blade mCPX V1 BL, Walkera Mini CP BL, Walkera QR Ladybird, Walkera Hoten X, Walkera Master CP.

Last edited by CX2Pilot; 09-11-2012 at 04:33 PM..
CX2Pilot is offline        Reply With Quote
Old 09-08-2012, 08:04 AM   #54
Heishley
Registered Users
 

Join Date: Sep 2012
Location: Singapore
Default Wk2603 setup with v100d03bl

Hi cx2pilot,

I cant seem to find a setup for V100D03BL with 2603 tx and rx2620.
Appreciate if you could help me with the beginner and advance settings for 3D.

Thanks in advance sir.
Heishley is offline        Reply With Quote
Old 09-08-2012, 04:29 PM   #55
CX2Pilot
Forum Support
 
Posts: 693
Thread Starter Thread Starter
 

Join Date: Jun 2008
Location: Cleveland, Ohio
Default

Hi,

I don't have the 2603 TX, just have the WK-2801 Pro.
The 2603 has limited programming but you can
use the D/R switch, EXPO, and PIT/PLT adjustments for beginner and
advance settings. You will have to program them for beginner
or 3D flying, you can't do it for both like you can with the WK-2801.
This will be turning knobs until you get the response you want.
There are no value screens for them so I can't give you some values to try.

The V100D03BL owners manual should have the setup for your 2603 TX.



Tom
__________________
Moderator for the Blade and Walkera Forums.
Walkera V100D01 V2 DBL, Walkera 4G6 w/RX2610V2, Align T-Rex 450SE V2, Blade mCPX V1 BL, Walkera Mini CP BL, Walkera QR Ladybird, Walkera Hoten X, Walkera Master CP.
CX2Pilot is offline        Reply With Quote
Old 09-08-2012, 07:59 PM   #56
Heishley
Registered Users
 

Join Date: Sep 2012
Location: Singapore
Default

Hi tom,

Guess i have to play around with the tx which kinda frustating to do.
Anyway thanks for your fast response.
This is a great place with tons of information for walkera heli settings.

Cheers,

Heishley
Heishley is offline        Reply With Quote
Old 09-08-2012, 10:08 PM   #57
CX2Pilot
Forum Support
 
Posts: 693
Thread Starter Thread Starter
 

Join Date: Jun 2008
Location: Cleveland, Ohio
Default

Hi Heishley,

Here is the manual for your 2603 TX, see link below.

See page 15 & 16.

Exponential function

V2 knob



See page 18.

7.3 dual rate


For beginner settings use the Dual Rate switch on your TX and set the
Exponential V2 knob as high as you want.

For 3D flight don't use the Dual Rate switch and use little or no Exponential.

You can also tame the heli down some with PIT using less of it.
It will give you less pitch. This in addition with using Dual Rate and EXPO.
For 3D go as high as you can with PIT without bogging the motor down.


Go to the bottom of the page and click the "Manual" icon.

http://www.walkera.com/en1/particular.jsp?pn=W22603




Tom
__________________
Moderator for the Blade and Walkera Forums.
Walkera V100D01 V2 DBL, Walkera 4G6 w/RX2610V2, Align T-Rex 450SE V2, Blade mCPX V1 BL, Walkera Mini CP BL, Walkera QR Ladybird, Walkera Hoten X, Walkera Master CP.
CX2Pilot is offline        Reply With Quote
Old 09-10-2012, 03:27 AM   #58
Heishley
Registered Users
 

Join Date: Sep 2012
Location: Singapore
Default

Hi tom,

Yeah it works now!! Its flying great with some 3d moves now. Got to tweak more to perform better. Thanks for your tips on the setup.
Heishley is offline        Reply With Quote
Old 09-11-2012, 04:30 PM   #59
CX2Pilot
Forum Support
 
Posts: 693
Thread Starter Thread Starter
 

Join Date: Jun 2008
Location: Cleveland, Ohio
Default Setup for the Walkera V120D02S V2

22. How to setup the Walkera V120D02S V2 - RX-2636H-D Receiver - Devo Transmitter


Type- Helicopter


SWASH - 1 Servo Normal


STMOD - MODE2 if you want the throttle on the left stick


REVERS - All normal


THHLD - STATE - ACT

POSIT - 0.0%

Set throttle trim to center.





Device Output


Devo 6


Gear - GEAR SW - GYRO
Pitch - System - Active



Devo 7

Gear - GEAR - ACT
AUX2 - AUX2 - GYRO



Devo 8S

Gear - GEAR SW - Active

Pitch - System - Active

AUX2 - FMOD SW - Gyro

AUX3 - RUDD D/R - Active




Devo 10

Gear - GEAR SW

Function - Active


AUX2 - FMOD SW

Function - Gyro



Devo 12S

Gear - GEAR SW - Active

Pitch - System - Active

AUX2 - AUX2 Lever - Gyro

AUX3 - AUX3 Lever - Active

AUX4 - AUX4 Lever - Active

AUX5 - AUX5 Lever - Active

AUX6 - AUX6 Knob - Active

AUX7 - AUX7 Knob - Active




Gyro Sensor

Mode - Manual

Switch - Mix SW

Pos 0 = 80.0%

Pos 1 = 75.0%

Pos 2 = 50.0%



Throttle Curve

Normal Flight

L= 0%

M= 50%

H= 100%


Stunt 1

L= 100%

M= 75%

H= 100%


Stunt 2

L= 100%

M= 75%

H= 100%



Pitch Curve

Normal Flight

L= - 20%

M= + 20%

H= + 56%


Stunt 1

L= - 56%

M= + 0%

H= + 56%


Stunt 2

L= - 56%

M= + 0%

H= + 56%




DR&EXP:

Set D/R and EXPO to your personal needs/preference. These should be good for beginners.
You can set more or less than 70% D/R if you want and more or less than +30% EXPO if you want.


ELEV D/R - 70% EXP +30%

AILE D/R - 70%, EXP +30%

RUDD D/R - 100%, EXP LIN

-
__________________
Moderator for the Blade and Walkera Forums.
Walkera V100D01 V2 DBL, Walkera 4G6 w/RX2610V2, Align T-Rex 450SE V2, Blade mCPX V1 BL, Walkera Mini CP BL, Walkera QR Ladybird, Walkera Hoten X, Walkera Master CP.
CX2Pilot is offline        Reply With Quote
Old 09-11-2012, 04:38 PM   #60
CX2Pilot
Forum Support
 
Posts: 693
Thread Starter Thread Starter
 

Join Date: Jun 2008
Location: Cleveland, Ohio
Default Setup for the Walkerx Hoten - X

23. How to setup the Walkera Hoten-X - RX2635H-D Receiver - Devo Transmitter.

These settings are for the Devo 6, Devo 7, Devo 7E, Devo 8S, Devo 10, and Devo 12S transmitters.



Select a new model or you can reset a current model.
All the other settings will be defaults that I don't list below.



Model -Type- HELI


SWASH - 1-NRM


STMOD - MODE2 if you want the throttle on the left stick


REVERS - All normal





FMOD Switch toggels between 6 axis mode and 3 axis mode
when you set the Device Output to the settings listed below.

FMOD 0 = 6 axis mode - Red flashing LED's
FMOD 1 = 6 axis mode - Red flashing LED's
FMOD 2 = 3 axis mode - Blue flashing LED's





Device Output


Devo 6


Gear - FMOD SW - Active

Pitch - System - Active





Devo 7

Gear - GEAR - ACT

AUX2 - FMD - ACT



Devo 7E

Gear- HOLD SW - Active

AUX2 - FMOD SW - Active




Devo 8S

Gear - GEAR SW - Active

Pitch - System - Active

AUX2 - FMOD SW - Active

AUX3 - RUDD D/R - Active



Devo 10

Gear - GEAR SW - Active

AUX2 - FMOD SW - Active

AUX3 - RUDD D/R - Active

AUX4 - AUX4 KB - Active

AUX5 - AUX5 KB - Active



Devo 12S

Gear - GEAR SW - Active

Pitch - System - Active

AUX2 - FMOD SW - Active

AUX3 - AUX3 Lever - Active

AUX4 - AUX4 Lever - Active

AUX5 - AUX5 Lever - Active

AUX6 - AUX6 Knob - Active

AUX7 - AUX7 Knob - Active





THHLD - STATE - ACT

POSIT - 0.0%

Set throttle trim to center.




DREXP

These should be good for beginners to start with.

You can use more or less D/R and more or less Expo if you need to.



ELEV D/R - 70% EXP +30%

AILE D/R - 70%, EXP +30%

RUDD D/R - 100% EXP LIN



If the above is not tame enough try these.
Adjust D/R and EXPO more or less to meet your needs.



ELEV D/R - 50% EXP +35%

AILE D/R - 50%, EXP +35%

RUDD D/R - 100% EXP LIN





If you want more agressive 3D mode try these settings.

ELEV D/R - 110% % EXP LIN

AILE D/R - 110%, EXP LIN

RUDD D/R - 120%, EXP -20 % > You can even try 150% for RUDD and more negitave EXP for fast rudder response.



TRVAD

AILE - U & D 120%

ELEV - L & R 120%

RUDD - L & R 120%


-
__________________
Moderator for the Blade and Walkera Forums.
Walkera V100D01 V2 DBL, Walkera 4G6 w/RX2610V2, Align T-Rex 450SE V2, Blade mCPX V1 BL, Walkera Mini CP BL, Walkera QR Ladybird, Walkera Hoten X, Walkera Master CP.

Last edited by CX2Pilot; 09-11-2012 at 11:39 PM..
CX2Pilot is offline        Reply With Quote
Reply




Unregistered
Go Back   HeliFreak > R/C Helicopter Support > Walkera Helicopters


Walkera Helicopters Walkera Helicopter Support

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Copyright © 2004-2011 - William James - Helifreak.com