START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
700 Class Nitro Helicopters 700 Class Nitro Helicopters manufactured by Align, Tarot, SYMA, Airhog, Chaos, HK and similar. |
|
LinkBack | Thread Tools | Display Modes |
04-26-2012, 08:58 AM | #1 (permalink) |
Registered Users
Join Date: Oct 2009
|
DS 610 Failure!
Turfed in my 700 yesterday due to a servo failure. I have the 700 3G all stock and was only about a minute into the flight. I did an aileron roll and it would not stop rolling. It went into a freshly plowed field so the damage was limited to main and tail blades, landing gear, boom and TT, canopy, and of course the servo. Luckilly it hit on the right side so the muffler is untouched. Once I had it on the bench, the aileron servo ,once powered up, just went full over and stayed there. I'll post a couple of pics soon.
__________________
Blade MCP-X Brushless, 300CFX, , Trex 450 Pro v2, Trex 600 ESP 6s 3GX v.3.1 and KDE head, Rotormast V-22, Futaba 12Z controle!! |
Sponsored Links | |||
Advertisement |
|
04-26-2012, 10:13 AM | #2 (permalink) |
Registered Users
Thread Starter
Join Date: Oct 2009
|
A few pics. Its about a $350.00 repair bill
__________________
Blade MCP-X Brushless, 300CFX, , Trex 450 Pro v2, Trex 600 ESP 6s 3GX v.3.1 and KDE head, Rotormast V-22, Futaba 12Z controle!! |
04-26-2012, 10:22 AM | #3 (permalink) |
Registered Users
|
sucks man.. ive had 610s for years and never had 1 fail..
they really are good servos.. and reports of failures really are few and far between. rebuild it! sorry for the damage.. that always sucks.
__________________
|
04-26-2012, 11:18 AM | #4 (permalink) |
Registered Users
Join Date: Feb 2008
|
she's very dirty, you'll be cleaning for awhile. Sorry for your loss, build it back up again and go flying ASAP. Rare occurrence, but it happens.
__________________
At the precipice, we change! Team GrandRC |
04-26-2012, 03:44 PM | #5 (permalink) |
Registered Users
Thread Starter
Join Date: Oct 2009
|
Got most of the cleanup done. I went through the engine and made sure any dirt was flushed out of the inside. I also removed the old clutch liner and will replace it. A hot start made it smell funny. Now I just have to wait on parts. I also changed out all the 610s with Hitec's
__________________
Blade MCP-X Brushless, 300CFX, , Trex 450 Pro v2, Trex 600 ESP 6s 3GX v.3.1 and KDE head, Rotormast V-22, Futaba 12Z controle!! |
04-27-2012, 07:25 AM | #7 (permalink) |
Registered Users
Join Date: Jul 2007
|
Hope you get it back in the air soon!
__________________
|Michalis| ...let the flying be second nature! |
04-27-2012, 08:07 AM | #8 (permalink) |
Registered Users
Thread Starter
Join Date: Oct 2009
|
Thanks. I should have all the parts by the middle of next week. Looks like we are going to have some nice weather next week as well!
__________________
Blade MCP-X Brushless, 300CFX, , Trex 450 Pro v2, Trex 600 ESP 6s 3GX v.3.1 and KDE head, Rotormast V-22, Futaba 12Z controle!! |
04-27-2012, 08:15 AM | #9 (permalink) |
Registered Users
Join Date: Jul 2008
|
i had a 610 go full over a while back on my 700 with the same result. that was an anamoly beacause since that time i have flown crashed 610s that work fine. that servo had been in a crash. i still fly them in 4 different helis and on an airplane. given the number that are sold the failure rate is extremely low and they are a good servo. sorry abouy your crash.....it's a terrible feeling to go from pilot to spectator.
|
04-27-2012, 10:52 AM | #10 (permalink) |
Registered Users
Thread Starter
Join Date: Oct 2009
|
Yep, it sucks. I'll probably be very nervouse the first couple of flight again!!
__________________
Blade MCP-X Brushless, 300CFX, , Trex 450 Pro v2, Trex 600 ESP 6s 3GX v.3.1 and KDE head, Rotormast V-22, Futaba 12Z controle!! |
04-28-2012, 01:40 PM | #11 (permalink) |
Registered Users
Thread Starter
Join Date: Oct 2009
|
Got some of the parts in today. WOOHOO!
__________________
Blade MCP-X Brushless, 300CFX, , Trex 450 Pro v2, Trex 600 ESP 6s 3GX v.3.1 and KDE head, Rotormast V-22, Futaba 12Z controle!! |
04-29-2012, 12:35 AM | #12 (permalink) |
Registered Users
Join Date: Nov 2010
|
How do I keep that from happening? Where your servo's binding by any chance?
|
04-29-2012, 08:13 AM | #13 (permalink) |
Registered Users
Thread Starter
Join Date: Oct 2009
|
No parts were binding at all. In fact I check all my linkages and screws after every outing. I give the swash and servo links a little twist back and forth to make sure they are riding smoothly on the balls with no stiffies. The only indication I had was that when I went into my first roll, it drifted bad to the right. I thought maybe my timing was off so I did another one! BIG MISTAKE. That is when it locked over. The preflight checks were all good on the swash.
__________________
Blade MCP-X Brushless, 300CFX, , Trex 450 Pro v2, Trex 600 ESP 6s 3GX v.3.1 and KDE head, Rotormast V-22, Futaba 12Z controle!! |
04-29-2012, 03:18 PM | #14 (permalink) |
Registered Users
Join Date: Jul 2007
|
I never had a DS610 fail but i had a brand new DS510 fail on my Trex500. It failed before the maiden flight when i was testing at the bench.
__________________
|Michalis| ...let the flying be second nature! |
04-30-2012, 02:47 AM | #15 (permalink) |
Registered Users
|
Had a 610 fail on my 50size last year. Not a funny thing to experience. Pilot errors are ok, but all other crashes hurts a lot more.
__________________
700E DFC - Ikon 700N FBL - Ikon |
04-30-2012, 08:05 AM | #16 (permalink) |
Registered Users
Join Date: Mar 2011
|
The only only heli I have with 610s is my 550 and they have worked flawless. All my other helis have Futaba BLS servos. I actually also use 650s for throttle servos.
|
05-04-2012, 11:03 AM | #17 (permalink) |
Registered Users
Thread Starter
Join Date: Oct 2009
|
Test hover went very well with the new servos. I was worried about the 7955's because they are a little slower than the 610's. But every stuf is working great!! Now I'm just waiting on my new canopy. Should be here this day!
__________________
Blade MCP-X Brushless, 300CFX, , Trex 450 Pro v2, Trex 600 ESP 6s 3GX v.3.1 and KDE head, Rotormast V-22, Futaba 12Z controle!! |
05-04-2012, 11:24 PM | #18 (permalink) |
Registered Users
Join Date: Sep 2010
|
Thats awesome Steve,glad things are going good ..
__________________
Team Align |
05-05-2012, 11:03 AM | #19 (permalink) |
Registered Users
Thread Starter
Join Date: Oct 2009
|
Thanks! I can't wait to get some time on it again. Its been WINDY for a week strait now and its trying to snow this morning to boot. Next week looks good though.
__________________
Blade MCP-X Brushless, 300CFX, , Trex 450 Pro v2, Trex 600 ESP 6s 3GX v.3.1 and KDE head, Rotormast V-22, Futaba 12Z controle!! |
05-07-2012, 08:36 AM | #20 (permalink) |
Registered Users
Thread Starter
Join Date: Oct 2009
|
Got a couple of flights on yesterday and every thing seems good. The Hitec 7955's are just fine for the 3G system even though they are a little slower than recomended.
__________________
Blade MCP-X Brushless, 300CFX, , Trex 450 Pro v2, Trex 600 ESP 6s 3GX v.3.1 and KDE head, Rotormast V-22, Futaba 12Z controle!! |
Thread Tools | |
Display Modes | |
|
|