Register Now

michael88997 · 01-26-2013, 02:08 PM

made a video

[ame]https://www.youtube.com/watch?v=XporLKq4tss&list=UUAMtbH-ziDdYWgHFncBkLTQ&index=1[/ame]

el guapo · 01-26-2013, 03:37 PM

Quote:

Originally Posted by michael88997

Well I had max Headspeed set to 2300, I had my normal throttle curve set to 0 at low then 60% flat line, when I brought the stick up to Max in normal mode it is 60% and the program is showing requested that low, the actual seems right but idk why the program is showing requested only in the 400's... How long does the soft start take to disengage?

"requested" is pretty much straight from your radio. its just telling you that at your current throttle position you have requested 447RPM.

your issue is between your radio and the vbar. you probbaly have to increase the end point in you radio and set you throttle curve to 100%.

test to make sure you get 100% at the arrow I drew on the attached photo.

michael88997 · 01-26-2013, 03:48 PM

Ya it's adjusted... And it was a flat line 60%... It seems to work fine with just a nicd pack... Ill try idle up and see what it does

michael88997 · 01-26-2013, 04:29 PM

ok got it working... i guess 60% is too low to test but once i jumped it to 100% the requested moved up... hopefully can try it out tomorrow. thanks

el guapo · 01-26-2013, 11:28 PM

make sure you lower the gain.

michael88997 · 01-26-2013, 11:39 PM

ya i set it to 25 per mrmel's video

el guapo · 01-26-2013, 11:43 PM

Quote:

Originally Posted by michael88997

ya i set it to 25 per mrmel's video

I think I had to go to 20. bring a lap top.
I wasted a few days trying to dial in pre comp to the tail and the gov. lowering the gain worked.

michael88997 · 02-02-2013, 03:10 PM

So I tried the gov out today and my hs was pretty low, I had to raise my throttle end point to 125% to get my hs around 2300 rpm, I did calibrate my throttle and set the gear ratio correct... What else could It be?

maarset · 02-02-2013, 08:52 PM

Which gov?

Sent from my iPhone using Tapatalk

michael88997 · 02-03-2013, 12:17 AM

maarset · 02-03-2013, 09:39 AM

What did you set your max HS to be in gov 2 tab?

Sent from my iPhone using Tapatalk

michael88997 · 02-03-2013, 10:03 AM

i set max at 2300 rpm... my idle up was 100% flat curve... i raised my endpoints in my tx to 125% and it was at the 2300rpm, but i had already programmed it at 100% in the vbar which my endpoint was around 98%

01-26-2013, 11:28 PM	#105 (permalink)
el guapo Registered Users Join Date: Dec 2010	make sure you lower the gain. __________________ Greg MSH USA Heli Flight Team Mikado V Team Lynx

02-02-2013, 08:52 PM	#109 (permalink)
maarset Registered Users My HF Map location Join Date: Feb 2008	It's official!!!! Which gov? Sent from my iPhone using Tapatalk

02-03-2013, 12:17 AM	#110 (permalink)
michael88997 Registered Users Thread Starter Join Date: Mar 2008 Location: Denton, TX	Vbar

02-03-2013, 09:39 AM	#111 (permalink)
maarset Registered Users My HF Map location Join Date: Feb 2008	It's official!!!! What did you set your max HS to be in gov 2 tab? Sent from my iPhone using Tapatalk

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-26-2013, 02:08 PM	#101 (permalink)
michael88997 Registered Users Thread Starter Join Date: Mar 2008 Location: Denton, TX	made a video [ame]https://www.youtube.com/watch?v=XporLKq4tss&list=UUAMtbH-ziDdYWgHFncBkLTQ&index=1[/ame]

01-26-2013, 03:48 PM	#103 (permalink)
michael88997 Registered Users Thread Starter Join Date: Mar 2008 Location: Denton, TX	Ya it's adjusted... And it was a flat line 60%... It seems to work fine with just a nicd pack... Ill try idle up and see what it does

01-26-2013, 04:29 PM	#104 (permalink)
michael88997 Registered Users Thread Starter Join Date: Mar 2008 Location: Denton, TX	ok got it working... i guess 60% is too low to test but once i jumped it to 100% the requested moved up... hopefully can try it out tomorrow. thanks

01-26-2013, 11:39 PM	#106 (permalink)
michael88997 Registered Users Thread Starter Join Date: Mar 2008 Location: Denton, TX	ya i set it to 25 per mrmel's video

02-02-2013, 03:10 PM	#108 (permalink)
michael88997 Registered Users Thread Starter Join Date: Mar 2008 Location: Denton, TX	So I tried the gov out today and my hs was pretty low, I had to raise my throttle end point to 125% to get my hs around 2300 rpm, I did calibrate my throttle and set the gear ratio correct... What else could It be?

02-03-2013, 10:03 AM	#112 (permalink)
michael88997 Registered Users Thread Starter Join Date: Mar 2008 Location: Denton, TX	i set max at 2300 rpm... my idle up was 100% flat curve... i raised my endpoints in my tx to 125% and it was at the 2300rpm, but i had already programmed it at 100% in the vbar which my endpoint was around 98%

Register Now

Log-in