Outrage 50 Nitro

[nate735]

Any updates.. ? Let's see some pics !

[FIGAAATELLU]

hi guys

is there some news ??
when this beast is supposed to be in our hand ???



i cant wait anymoreeee!!

[Foxden]

The Factory Pilots have to get the prototypes first, test them and get info back to the designer for modification. We are hoping the prototypes will be here soon

[DominicD]

Charley posted these on the otheRR site today.

[fiveoboy01]

Pic fail.

[Charley Stephens]

I posted this on the other site today

Here is a quick shot next to a retired 50

PLEASE NOTE this is a CONCEPT MODEL and has changed some compared to the current model but you can get an idea of its size

Information I have to share so far is
Model has
8.6:1 Main Gear ratio .8mod tooth
4.58 Tail Ratio
TT Drive
Capable to swing 620mm blades with 95mm Tail Blades with room to spare

Also look at cad renders to give you an idea how wide the canopy is if it was any narrower it would be part of the frame

[billbill242000]

Any chance of a hint as to what the test pilots are running in it?? Motor,servos,gov,that sort of thing...getting ready to start filling the cart and just looking for a little guidance...
Can't wait to start getting all the new shiny pieces all laid out on the table.....

[LITHIUMSTATIC]

Originally Posted by billbill242000

Any chance of a hint as to what the test pilots are running in it?? Motor,servos,gov,that sort of thing...getting ready to start filling the cart and just looking for a little guidance...
Can't wait to start getting all the new shiny pieces all laid out on the table.....

They don't have prototypes yet...

[Foxden]

What we've already started to put aside:

TT53 w/Outrage N50 pipe
InoLab 760 servo's
Spartan Gyro w/ jr 8900
Perfect Regulators new reg
MultiGov Pro Gov
Outrage Rx pack
Spectrum rcvr

[billbill242000]

So your not gonna run a AR7100R and use the rev limiter and regulator thats built into it? I thought that might be a good thing to do to save weight.

[Foxden]

Originally Posted by billbill242000

So your not gonna run a AR7100R and use the rev limiter and regulator thats built into it? I thought that might be a good thing to do to save weight.

I perfer a full govenor over the rev limiter, I'll either use the Spectrum sensor pickup or a Hotwings opticle sensor and already have a 7100 and a pair of 9100 receivers, I don't think using a 7100 and a MultiGov Pro will add enough weight to worry about, I'm also going to give the Perfect Regulators a try and waiting to get the 10amp bec from Matt to test out as well on our O550, we'll see my thoughts may change when I have the prototype build and see what kind of room I have available for mounting.

[nate735]

Any pics from a side angle, so we can see the frames and servo layout ?

[Foxden]

Originally Posted by nate735

Any pics from a side angle, so we can see the frames and servo layout ?

I'm pretty sure the servo layout is the exact same setup as the Outrage 550

[trextuning]

pics are up on the outrage-tuning blog showing frames and tail gearbox in detail, just got the piccies today.

[Charley Stephens]

Originally Posted by trextuning

pics are up on the outrage-tuning blog showing frames and tail gearbox in detail, just got the piccies today.

Yes we are getting closer! just note those are rev2 frames I have changed more since then and may change again after testing will know more in just a short time leave wednesday to go fly it

[DominicD]

This thread is worthless without videos

[trextuning]

Yes we are getting closer! just note those are rev2 frames I have changed more since then and may change again after testing will know more in just a short time leave wednesday to go fly it

OK Charley, I'll make that note against the piccies, as always prototypes are works in progress and changes inevitably happen, that's the point of prototypes

[billbill242000]

I think I'm nuts!!! $1670 so far and it's not even on the market yet.....
Man I can't wait!! :o:o:o

[HeliHobbyPRO]

Well that looks like a great heli !