START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
DJI Heli Autopilot System(Naza-H/WooKong-H/Ace One) DJI Heli Autopilot System(Naza-H/WooKong-H/Ace One) Factory Support Forum |
|
LinkBack | Thread Tools | Display Modes |
02-15-2013, 02:47 PM | #1 (permalink) |
Registered Users
|
Center stick changes in modes - Naza
Is this right? I have everything zeroed on the radio and it is perfectly centered in manual mode. I have tried recalibrating it in all modes = no change.
__________________
Dan Da Dawg - JR X9303 Hexa F550 on 3S + 6S TREX 500 + 6S TREX 600 + Blade mSR + Blade mCPx2 Brushless + 12S Rave FBL ENV |
Sponsored Links | |||
Advertisement |
|
02-15-2013, 02:54 PM | #2 (permalink) |
Registered Users
|
I would recomend pulling up the servo monitor on the transmitter and see if anything is happening on the respective channel there, might be a hover pitch or rpm setting or something if you are using a Heli-model on the transmitter..
__________________
Helibug Mercury 800, Henseleit TD-NT, Henseleit TDR, Tarot FY680, XuGong-10, TBS Disco PRO, Blackout Miniquad, Futaba 14SG, EZuhf. |
02-15-2013, 03:05 PM | #3 (permalink) |
Registered Users
Thread Starter
|
Nope. Monitor is good. Only thing moving is pitch. Yes, I am using Idle Up 1 and 2 to switch modes on the pitch but I to not have anything mixed or linked. It is the only one changing.
__________________
Dan Da Dawg - JR X9303 Hexa F550 on 3S + 6S TREX 500 + 6S TREX 600 + Blade mSR + Blade mCPx2 Brushless + 12S Rave FBL ENV |
02-15-2013, 03:47 PM | #4 (permalink) |
Registered Users
|
hmm..and this is only happening mid-stick on the throttle?
are you using PPM between receiver and NAZA? I use Gyro gain linked to flight mode in the transmitter to change between flight modes on the NAZA, This is on a futaba system, but I think your JR have similar possibilities... You are after all changing the setting on the "Gyro" not the pitch
__________________
Helibug Mercury 800, Henseleit TD-NT, Henseleit TDR, Tarot FY680, XuGong-10, TBS Disco PRO, Blackout Miniquad, Futaba 14SG, EZuhf. |
02-15-2013, 06:44 PM | #5 (permalink) |
Registered Users
|
If I am understanding this correctly when you switch from manual mode to Atti mode you are getting movement on you elevator channel in the Naza software but its not showing any movement on your radio monitor screen?
__________________
Trex 700N, 700E, 600E, 500E all Vbar 5.2 Pro FBL Dji F550 WKM Data Link 900MHZ DJI F450 Naza/GPS FPV 5.8 vtx TBS Disco w Core Naza GPS FPV 1.2 vtx MT Tiger motors |
02-16-2013, 06:21 AM | #6 (permalink) |
Registered Users
Thread Starter
|
Re: Center stick changes in modes - Naza
Deuce-Correct I have not changed anything from the way we set up earlier. I just noticed that aileron and elevator were changing slightly when I was flipping from GPS to atti to manual
Sent from Galaxy S3
__________________
Dan Da Dawg - JR X9303 Hexa F550 on 3S + 6S TREX 500 + 6S TREX 600 + Blade mSR + Blade mCPx2 Brushless + 12S Rave FBL ENV |
02-16-2013, 06:54 AM | #7 (permalink) |
Registered Users
Join Date: Sep 2012
|
When you calibrated the sticks, did you ensure everything was dead center when you confirmed? Are there any mixes programmed into your Tx?
Try posting in the RCTech subforum over at http://fpvlab.com. |
02-16-2013, 10:06 AM | #8 (permalink) |
Registered Users
|
Might be caused by PPM timing changes if you use PPM....
__________________
Helibug Mercury 800, Henseleit TD-NT, Henseleit TDR, Tarot FY680, XuGong-10, TBS Disco PRO, Blackout Miniquad, Futaba 14SG, EZuhf. |
02-16-2013, 07:07 PM | #9 (permalink) |
Registered Users
Thread Starter
|
Deuce wins again. When I first reprogrammed the model I changed from Arco to heli and "thought" I had cleared or zeroed everything. Deuce PM'ed me and asked "are you SURE you cleared everything?"
Me: not 100% So... I took pictures of all my screens, made a new model, and verbatim put everything back. The problem went away! Thanks Bri!
__________________
Dan Da Dawg - JR X9303 Hexa F550 on 3S + 6S TREX 500 + 6S TREX 600 + Blade mSR + Blade mCPx2 Brushless + 12S Rave FBL ENV |
Thread Tools | |
Display Modes | |
|
|