Here is my mcpx brushless conversion with pics ,still video and flight video

[decompyler]

I try to keep my length as short as possible without having contact with the blades. It keeps the ballance nice. I'm at 151 main shaft to tail shaft.

[whoanelly]

Heres mine with the upgrdes,,dam animal


[ame]http://www.youtube.com/watch?v=02nGfMDdHBg&list=UU1nF0efo5jrrEOFbxFwKBKg& index=1&feature=plcp[/ame]

[Diablol]

[ame]http://www.youtube.com/watch?v=CGqhfKnXdqI[/ame]

[Spunjah413]

Great vid Diablol. Curious what your total weight is with batts?

Also that is a bit lacking in the best/strongest 1S category (Was reading your video information). My 915 has tached 7500-7700 RPM peak with 220G consistant negative thrust on a scale. Using the XP12A w/ BLHeli flash on a 9T w/ Hyp 550's.

[Diablol]

I know that is not "the strongest" any more since the 915 . I was just happy about the power . I think the weight was about 70-75 gramms. I dont have it anymore..building 2s/3s..need for more.

[Aries17q]

Here is my Blade MCPx V.1 Brushless setup

DIY Canopy
Micro Heli Swashplate, Head, Aluminum Boom
Esky solid metal main shaft modified
Walkera Carbon Boom Support
DIY Carbon Fin
Original Main Blade Painted in Yellow
SR120 Tail Motor & Rotor with modified Twisted Pair Cable
Brushless Walkera Inrunner 11,000kv, 9T Pinion
Brushless Walkera WST-10A-ESC
JST Plug conversion
500mah 15C Eflight for SR120
Original Main Frame and Skids

DX6i
Travel Adjust ( 90%, 90%)
Iddle up - (100% Flat)

The Steve Converter (Yellow cable direct solder back of the signal board, white from the steve to esc signal, Red & Black power for the steve in front of the board near below the Tail FET) ESC Power direct solder to (+,-) of the board

Additional 2mm foam tape attached to all servo board to avoid heat transfer from motor.

[tntburnett]

Originally Posted by Aries17q

Here is my Blade MCPx V.1 Brushless setup

DIY Canopy
Micro Heli Swashplate, Head, Aluminum Boom
Esky solid metal main shaft modified
Walkera Carbon Boom Support
DIY Carbon Fin
Original Main Blade Painted in Yellow
SR120 Tail Motor & Rotor with modified Twisted Pair Cable
Brushless Walkera Inrunner 11,000kv, 9T Pinion
Brushless Walkera WST-10A-ESC
JST Plug conversion
500mah 15C Eflight for SR120
Original Main Frame and Skids

DX6i
Travel Adjust ( 90%, 90%)
Iddle up - (100% Flat)

The Steve Converter (Yellow cable direct solder back of the signal board, white from the steve to esc signal, Red & Black power for the steve in front of the board near below the Tail FET) ESC Power direct solder to (+,-) of the board

Additional 2mm foam tape attached to all servo board to avoid heat transfer from motor.

Looking good .

Be blessed
Isaac

Sent from my DROIDX using Tapatalk 2

[Aries17q]

Thanx Tnt, you are the man and you have inspired me for this upgrades. Thanks to liftbag aswell for his creations...

[Aries17q]

Here is my Brushless MCPx V1 raw Video idle-up pitch indoor test, this thing has too much power, BAMmm.. almost cut the leg of the dining table........but still flies great.




[ame]http://www.youtube.com/watch?v=Dile7w3E4c4[/ame]




Aries17mq

[tntburnett]

Originally Posted by Aries17q

Here is my Brushless MCPx V1 raw Video idle-up pitch indoor test, this thing has too much power, BAMmm.. almost cut the leg of the dining table........but still flies great.




http://www.youtube.com/watch?v=Dile7w3E4c4




Aries17mq

Be careful with in the house doing pitch pumps.

Be blessed
Isaac

Sent from my DROIDX using Tapatalk 2

[Dutch349311]

Originally Posted by whoanelly

Heres mine with the upgrdes,,dam animal


http://www.youtube.com/watch?v=02nGf...1&feature=plcp

Amazing!!! It's great watching this Heli fly!!! This Heli sold me and I expect kit today and now eflite comes out with blade130x!!!! And it's TT with variable pitch tail!!! Never fails

[ame]http://www.youtube.com/watch?v=m7fiC5NrtzA&feature=youtube_gdata_player[/ame]

[Chris20]

That is freakin sweet! Now we all have to start over as the modding begins again.

[anjoi666]

heres my new monster! finally have video

mcpx hp06v2 sr120 tail 3d test (2 min 45 sec)

[fusionsx00]

Here is my newest mcpx V1 board-xp12a flashed/hp06v2/sr120 tail/ extreme frame/ plantranco prop



V1 board, steve/wst-10amp/hp05/sr120 tail plantranco/cnc swash

[Drivinfast247]

Originally Posted by whoanelly

Heres mine with the upgrdes,,dam animal


http://www.youtube.com/watch?v=02nGf...1&feature=plcp

She sounds mean!!

[Drivinfast247]

Diablol, that was INSANE!!!

[tanman]

mCP X 1 - light/indoor setup

MH X Frame
MH X Swash
Reverse Servos
Solid CF Shaft
Solid 2mm Boom
Xtreme Head
Stock Blade Grips
Grommets
Dual Coreless Tail with Astroid 6mm Inline Mount
Astroid Carbon Fin
DIY Boom Support with MH Boom Support Ends
C05M with 8T pinion
XP-7A flashed with BLHELI 3.4
Micro Deans
\















mCP x 2 - Outdoor/Medium Setup

MH X Frame
MH X Swash
Reverse Servos
Grommets
Solid CF Shaft
3mm Boom
Stock Blade Grips
Astroid Horizontal Stab
Astroid Derlin Anti-Rotation Bracket
Astroid Carbon Motor and Boom Support Mount
Astroid Boom Support
SR 120 Tail with DIY Tail Skid
RRC 65mm Rotor
XP-7A flashed with BLHELI 3.4
HP05S
Micro Deans



















Thanks to DoubleCH, Dylwad, liftbag, sskaug, 4712 and all the others for all the great information and inspiration. Another is on the way with HP06V2 and HP03 new version once every bits and pieces arrive

[tntburnett]

Looking real nice

Be blessed
Isaac

Sent from my DROIDX using Tapatalk 2

[eranbw]

RKH Mcpx 600mAh 1 cell 3D test (2 min 56 sec)

[eranbw]

[ame]http://www.youtube.com/watch?v=yuPqAZhmtjg&feature=plcp[/ame]