Register Now

d3sbo · 09-26-2010, 12:39 PM

i have my tail gain and Governor and FC all on the idle up switch
normal mode is no FC gain with a mix like the one shown for the Governor
this means you need a mix to have some FC gain using T hold
but as far i can see this only leave you with a 3 position switch for the auto trim not that i/we can use it

am using JR radio with gyro menu and Governor menu

EO19 · 10-21-2010, 07:32 PM

Make sure that when setting your low throttle that you set the trim to 3/4. I am running a V-curve in Idle 1 and 2. failed to do this and noticed that around center stick it was going into decay mode. I went back and set the low throttle again and it took care of it.

nwmtech · 10-21-2010, 08:48 PM

Why are you running such a low middle point on your V-Curve?

EO19 · 10-21-2010, 09:06 PM

Quote:

Originally Posted by nwmtech

Why are you running such a low middle point on your V-Curve?

I was running a Muti Gov pro at 100 - 80 - 100. I called and spoke to Brian and he said to run 100-65-100.

nwmtech · 10-22-2010, 02:35 PM

Hmm... even at 65 it should haven't shut TL off. I checked mine night and with my trim at 1/2 (where I always have it) mine didn't hit decay mode until 41% throttle.

nwmtech · 10-28-2010, 09:18 PM

Updated for recent info on Aux channel assignments changing flying characteristics.

dereksharp · 06-29-2011, 03:26 PM

I have the Total G with 3 sats and it binds ok, but after 3 or 4 flights (re-fueling and switching off/on) it loses the bind resulting in loss of control and costing me lots of heli coupons.
Any one had this? Any one know of a cure?
Never had this with Futaba.

09-26-2010, 12:39 PM	#21 (permalink)
d3sbo Registered Users Join Date: Feb 2007	i have my tail gain and Governor and FC all on the idle up switch normal mode is no FC gain with a mix like the one shown for the Governor this means you need a mix to have some FC gain using T hold but as far i can see this only leave you with a 3 position switch for the auto trim not that i/we can use it am using JR radio with gyro menu and Governor menu __________________ 2 x Blade MCPX,stock & duel Brushless Trex 250FBL,BeastX,Scorpion,Trex 450,Scorpion,4s,Jazz esc,Trex 500FBL,3GX V3.1,5s,Scorpion Avant, Kasama head,OS 91 OMI,XeroG Raptor,Total G,Outrage Head Trex 600 EFL Pro super combo,BeastX

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-21-2010, 07:32 PM	#22 (permalink)
EO19 Registered Users Join Date: Apr 2009	Make sure that when setting your low throttle that you set the trim to 3/4. I am running a V-curve in Idle 1 and 2. failed to do this and noticed that around center stick it was going into decay mode. I went back and set the low throttle again and it took care of it.

10-21-2010, 08:48 PM	#23 (permalink)
nwmtech Registered Users Thread Starter My HF Map location Join Date: Jul 2009	Why are you running such a low middle point on your V-Curve?

10-22-2010, 02:35 PM	#25 (permalink)
nwmtech Registered Users Thread Starter My HF Map location Join Date: Jul 2009	Hmm... even at 65 it should haven't shut TL off. I checked mine night and with my trim at 1/2 (where I always have it) mine didn't hit decay mode until 41% throttle.

10-28-2010, 09:18 PM	#26 (permalink)
nwmtech Registered Users Thread Starter My HF Map location Join Date: Jul 2009	Updated for recent info on Aux channel assignments changing flying characteristics.

06-29-2011, 03:26 PM	#27 (permalink)
dereksharp Registered Users Join Date: May 2009	I have the Total G with 3 sats and it binds ok, but after 3 or 4 flights (re-fueling and switching off/on) it loses the bind resulting in loss of control and costing me lots of heli coupons. Any one had this? Any one know of a cure? Never had this with Futaba.

Register Now

Log-in