DJI Naza-H GPS Flybarless System

[Wesley888]

Originally Posted by Hizlimax

The manual also states that the throttle locks to the current position when you switch to Atti or GPS modes and I don't get the logic in that. I guess I will just buy it or wait for a member to test it out

It is exactly that. Whatever the throttle is at when you switch to AH/GPS mode, the throttle will stay there regardless of what you are going to do with the throttle control. Even Throttle Hold from your controller won't change the throttle of the heli. NAZA-H will use the pitch to control up/down. Your throttle stick will simply telling NAZA-H how fast to go up/down related to it's hovering point.

[Hizlimax]

Originally Posted by Wesley888

It is exactly that. Whatever the throttle is at when you switch to AH/GPS mode, the throttle will stay there regardless of what you are going to do with the throttle control. Even Throttle Hold from your controller won't change the throttle of the heli. NAZA-H will use the pitch to control up/down. Your throttle stick will simply telling NAZA-H how fast to go up/down related to it's hovering point.

I rather have my TX Throttle Hold work as a separate switch when I flick it. I think locking the throttle from Naza limits the forward flight capabilities of the heli in Atti or GPS modes. You won't be able to switch flight modes when you are in Atti or GPS. Plus how will the Semi-auto Take-off & Landing work? We will spool it up with a flat %100 throttle curve at 0 pitch and then take off?

[Wesley888]

I think it'll work like their NAZA product for the multicopter. You do the special take off sticks sequence and the motor will spin up to a pre-determined throttle and take off using the throttle stick.

[NexxuSix]

DJI: Please see the other thread in this forum:

https://www.helifreak.com/showthread.php?t=446123

A lot of pilots are requesting RTH for safety purposes, and peace of mind. Please consider implementing this feature. Thank you!

[zeeflyboy]

Originally Posted by Hizlimax

Plus how will the Semi-auto Take-off & Landing work? We will spool it up with a flat %100 throttle curve at 0 pitch and then take off?

That's how I fly anyway tbh, I am always in idle up.

Flick off throttle hold and the ESC soft start takes care of the spool up, spins up to whatever speed you have set your curve at in idle up and then off you go...

On landing you just land, cut the throttle and let it spool down.

There is no problem in operating this way.

[Silverexpress01]

Check this out...

DJI Naza-H Assistant Software Configuration (15 min 22 sec)

DJI Naza-H Setup Demo (7 min 0 sec)

[DJI Innovations]

DJI Has Already Released Formally Naza Series Product——Naza-H GPS Helicopter System.

In order to help customers get rid of some confusions about Naza-H GPS functions, a thread created.

Naza-H GPS is not only an autopilot stabilization system (Attitude Mode & Gps Attitude Mode) included following all other DJI existing helicopter autopilot system, Ace One, Ace Waypoint and WooKong-H/WooKong-H Lite, but is a Flybarless System with very good performance ((Including Pirouette Compensation, Auto Trim, Suitable for Different Flying Styles, etc). You can check the video below.

Therefore, Naza-H is a good option for Flybarless System 3D Flight and Autopilot Stabilization Flight.

Naza-H Main Features:
All-in-One Design
Built-in Tail Gyro/Flybarless Supported
Support for Multiple Electric Helicopter Platforms
Advanced Attitude and Control Algorithm
Optional GPS Module
Multiple Flight Control Modes/Intelligent Switching
D-Bus Supported
Independent LED Module
Semi-auto Take-off & Landing （Will Be Available in The Following New Firmware）

Welcome your discussion, feedback and questions about Naza-H GPS?

DJI Naza-H Setup Demostration:



DJI Naza-H Assistant Software Configuration:



DJI Naza-H 3D Flight



DJI Naza-H 3D Flight in 3DX China 2012
[ame]http://www.youtube.com/watch?v=WISt-wXUG7k[/ame]

[ame]http://www.youtube.com/watch?v=-361nfshEyc[/ame]

DJI Naza-H GPS Atti.Mode with Position Lock

[Tahoe Ed]

Check this out:

https://www.helifreak.com/showthread.php?t=479611

If it works for you, let's start to consolidating the Naza H threads. I have closed this thread:

https://www.helifreak.com/showthread.php?t=448443

[DJI Innovations]

[ame]http://www.youtube.com/watch?v=WISt-wXUG7k[/ame]


[ame]http://www.youtube.com/watch?v=-361nfshEyc[/ame]

[arpakorn]

at gps mode(position hold) Can i use 6 channel radio(T6j)???

[zeeflyboy]

No, 7 channels minimum for the GPS mode option

[Tahoe Ed]

Originally Posted by zeeflyboy

No, 7 channels minimum for the GPS mode option

Zeeflyboy is correct, you need a 7 channel Tx and Rx preferably with preset failsafe.

[Azalin]

Guys
Do you think there will be a software upgrade to add governor into Naza-H?

[wonderd]

Why not use the ESC gov?

[Azalin]

To use Naza in the future on nitro helicopters.

[Tahoe Ed]

Nitro SRH is not supported now. Try the WKH or the Ace One for Nitro unless you want 3D, in that case you are SOL.

[gpbill]

Tahoe,
I've nearly finished the set up on my Trex 600 but there are a couple of questions I'm unable to find answers to.
First one is, when using a BEC, NAZA or any other shouldn't the hot wire be pulled from the ESC to prevent powering the MC from both sides?
Second, I am using a flybar. NAZA setup as me skip setting any pitch values and I don't see in the quick guide any thing about pitch or throttle curves.

[Tahoe Ed]

Originally Posted by gpbill

Tahoe,
I've nearly finished the set up on my Trex 600 but there are a couple of questions I'm unable to find answers to.
First one is, when using a BEC, NAZA or any other shouldn't the hot wire be pulled from the ESC to prevent powering the MC from both sides?
Second, I am using a flybar. NAZA setup as me skip setting any pitch values and I don't see in the quick guide any thing about pitch or throttle curves.

I have pulled the red, positive wire, from my esc. Your pitch and throttle curves are basically what is recommended by your heli mfg. I am not a 3d flyer so my set up is for a newbe or a scale flyer. Here is my set up: https://www.helifreak.com/showthread.php?t=479611. Thunder Fighter is more of a 3D guy on the tame side. His post are here; https://www.helifreak.com/showthread.php?t=479138. Take your pick. Either will work, but to different ends.

[Thunder Fighter]

I didn't mention in my post that I had already pulled the positive from my plug on my ESC. I think the positive and negative rail are common on all of the pins so this would be the right way to do it.

//Dennis.

[zeeflyboy]

Most HV ESCs don't have a BEC built in... In this case you can leave all three wires connected.

If however yours does have a BEC then quite correct - you want to remove at least the positive pin if using external power for the system.