Beastx Throttle Problem.

[Sladex]

The throttle doesnt work. Ive been looking around and i says that the esc has to beep. It only beeps when i put the 12s in. I am using a cc bec pro and the cc hv120

[K2Freak]

Are you sure that you calibrated the esc correctly? If not, go to the documents section of castle creations site and read about fep and gov setup. It must be done right...

[GT86]

Yep, that's probably the problem. You have to teach the esc what your throttle low and high points are.

http://www.castlecreations.com/support/documents.html and toward the bottom you'll see a how to on setting up fixed endpoints. You have to do this first even if you plan on using the governor.

Also, it won't arm unless it sees a zero throttle signal, so check and see that your throttle hold is set to zero.

Sent from my Galaxy Nexus using Tapatalk 2

[Sladex]

Originally Posted by GT86

Yep, that's probably the problem. You have to teach the esc what your throttle low and high points are.

http://www.castlecreations.com/support/documents.html and toward the bottom you'll see a how to on setting up fixed endpoints. You have to do this first even if you plan on using the governor.

Also, it won't arm unless it sees a zero throttle signal, so check and see that your throttle hold is set to zero.

Sent from my Galaxy Nexus using Tapatalk 2

I dont have the kit to plug it into my computer?

[K2Freak]

They gave you a gift cert for one in the package. Or if not then buy one. You need it to use the cc controller on a heli. Period. That should never have been optional.

You calibrate the endpoints without the castlelink, but probably a bad choice to try to fly - Too many settings not exposed via stick programming. You don't teach cc, you find the points with tx atv. Its not like hw, scorp.

And your throttle hold will not be zero. You will "find" that too.

Read those docs until you understand what you are doing. They are good.

[ddj74]

make sure your throttle curve is 0, 25, 50 , 75, 100

[Sladex]

It still doesnt work. ive got it to spin 3 times so far. But it the esc keeps blinking. I think that means it is in programming mode. My ATV Is L = 52% And H=102%. Something is wrong.

[Sladex]

Bump

[Sladex]

Come on guys i need this in the next few minutes

[ShaneJourdan]

Is your throttle curve set linear. 0 25 50 75 100



Sent from my iPad using Tapatalk HD

[Sladex]

Originally Posted by DoctorJ

Is your throttle curve set linear. 0 25 50 75 100



Sent from my iPad using Tapatalk HD

Yep

[K2Freak]

Castles have a light? I don't remember that.

Slow down and figure this out. You need the castlelink before you are going anywhere anyway.

[ShaneJourdan]

Opp's didn't see that was posted already.

When setting end points you set both to around 50%, then went high and it alerted at 102, sounds ok. Then you went low and it alerted at 52?? What?

You should be going down not up. But what ever this can't be right.



Sent from my iPad using Tapatalk HD

[Sladex]

Originally Posted by K2Freak

Castles have a light? I don't remember that.

Slow down and figure this out. You need the castlelink before you are going anywhere anyway.

I am gonna have to wait days for it to come. Isn't there a way to do it without it . The hv escs have a light on the side. It will basically ask you the questions through the light.

[Sladex]

Originally Posted by DoctorJ

Opp's didn't see that was posted already.

When setting end points you set both to around 50%, then went high and it alerted at 102, sounds ok. Then you went low and it alerted at 52?? What?

You should be going down not up. But what ever this can't be right.



Sent from my iPad using Tapatalk HD

Yeh. It alerted fine at 102 then I went beep beep beep really fast and then when I switched to low it did the same and beeped on 52. I think I know the culprit, the ar7200bx fail safe thingy

[ShaneJourdan]

Originally Posted by Sladex

I am gonna have to wait days for it to come. Isn't there a way to do it without it . The hv escs have a light on the side. It will basically ask you the questions through the light.

Good luck with that, you really need the cc link. Your in airplane mode.


Sent from my iPad using Tapatalk HD

[Sladex]

Originally Posted by DoctorJ

Good luck with that, you really need the cc link. Your in airplane mode.


Sent from my iPad using Tapatalk HD

Oh **** off course. Ty

[ddj74]

Originally Posted by Sladex

Yeh. It alerted fine at 102 then I went beep beep beep really fast and then when I switched to low it did the same and beeped on 52. I think I know the culprit, the ar7200bx fail safe thingy

Re-bind the controller but make sure you are at low stick and switches are at default settings such as throttle hold on or whatever. If a switch isn't in a certain position other then what it was when you bound the controller it will not initialize.

[Sladex]

Any other suggestion guys

[Sladex]

I need as many suggestions as possible