Register Now

Azzurra · 06-15-2007, 11:48 PM

Hi,

I replaced the stock ESC with the Align 75A. There is a setting for timing on this one; does anyone know, what timing is best. Otherwise I'll set on mid timing.

best

Carsten

badriM · 06-16-2007, 12:07 AM

hi,

I have also an align 75 and the mid timing is perfect for this engine.

Greats from Belgium

Azzurra · 06-16-2007, 12:09 AM

Thanks,

what pinion do you use? Du you use the governor mode?

cheers from Lake Constance

Carsten

Finless · 06-16-2007, 09:48 AM

For KV motors from about 1100 and below I have run HIGH timing (reccomended by Align) and noticed the motor ran cooler and had more power.
THis was true for my Hyperion 3025-10 on my Lepton.

Bob

X30PILOT · 06-16-2007, 09:48 PM

I’m using an Align 75 amp controller on my stock motor with a 14 tooth pinion.
I have it set up on high timing and no governor. With this combination I get just over 1990 rpm head speed at the start, going down to 1950 3.5 minutes into the flight turning a 500 mm set of Mikado blades. I have the throttle curve set up at 100-85-100.
Set up this way I have more power than the stock controller with no increase in motor temp or amp draw.

X30

06-15-2007, 11:48 PM	#1 (permalink)
Azzurra Registered Users Join Date: Jan 2007	What Timing for Stock Motor Hi, I replaced the stock ESC with the Align 75A. There is a setting for timing on this one; does anyone know, what timing is best. Otherwise I'll set on mid timing. best Carsten __________________ T-Rex 600 CF \| VBar \|TT\|Plettenberg 30-12HE\|JAZZ55-10-32\|3X9252\|9254\|FF-6, FASST\|Radix600\|SLS3700ZX 10s packs

06-16-2007, 12:09 AM	#3 (permalink)
Azzurra Registered Users Thread Starter Join Date: Jan 2007	Thanks, what pinion do you use? Du you use the governor mode? cheers from Lake Constance Carsten __________________ T-Rex 600 CF \| VBar \|TT\|Plettenberg 30-12HE\|JAZZ55-10-32\|3X9252\|9254\|FF-6, FASST\|Radix600\|SLS3700ZX 10s packs

06-16-2007, 09:48 AM	#4 (permalink)
Finless Team Taco VP My HF Map location Join Date: Nov 2005	For KV motors from about 1100 and below I have run HIGH timing (reccomended by Align) and noticed the motor ran cooler and had more power. THis was true for my Hyperion 3025-10 on my Lepton. Bob __________________ "Don't Taco My Pack Dude!" NEW Video Link -> Safety Video #1 Video Link -> CAUTION using powerful tools! Video Link -> How to CRASH TWICE in one flight! Video Link -> Don't Taco!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

06-16-2007, 12:07 AM	#2 (permalink)
badriM My HF Map location Join Date: Sep 2006	hi, I have also an align 75 and the mid timing is perfect for this engine. Greats from Belgium

06-16-2007, 09:48 PM	#5 (permalink)
X30PILOT Registered Users Join Date: May 2006	I’m using an Align 75 amp controller on my stock motor with a 14 tooth pinion. I have it set up on high timing and no governor. With this combination I get just over 1990 rpm head speed at the start, going down to 1950 3.5 minutes into the flight turning a 500 mm set of Mikado blades. I have the throttle curve set up at 100-85-100. Set up this way I have more power than the stock controller with no increase in motor temp or amp draw. X30

Register Now

Log-in