Register Now

helipainter · 08-29-2010, 02:24 PM

OK, so i managed to get my totalg installed, got everything setup but i am at a loss as to why my Governor settings can't be easier to figure out, moreso with the 11x. Anybody know why my governor window in 11x is greyed out like not accesible? Right now i have some mixing to aux5 but it only gave me two gov settings and left idle1 with no gov. Did i skip something setting it up?

I spooled her up and so far so good. It's a gasser so i was a little concerned

Once i understood how to sett the G up, it was a walk in the park. I feel like i forgot something, but it is ready to go except this governor issue. Thanks for any ideas you guys got

ncarbon · 08-29-2010, 04:12 PM

I have my GOV on the GEAR channel controled by the FMOD switch so I have OFF 1650 and 1950. In system menu under devices you have to choose the channel setting , INH ACT GYO GOV, but any channel after AUX3 only has INH ACT option. So my GOV is set for GEAR channel and in DEVICE I havr GEAR set to GOV. Hope this helps.

Ned

helipainter · 08-29-2010, 06:56 PM

That was what mine is setup like for the most part. So you have the gov off in norm, then it is on in idle1 and idle2? That makes since.

I see the word governor in my menu for the 11x, what governor does that work with? I'd love to see real numbers so i could adjust if i needed to in the field. I fly 300 miles from a computer. Right now like this i gotta have the PC to see what speeds i'm hitting with what endpoints.

ncarbon · 08-29-2010, 07:04 PM

I could tell you mine* the values and corresponding RPMs ?

Ned

helipainter · 08-30-2010, 07:49 AM

yes, i can get into the totalG software and see the values as i adjust them. lastnight i was able to mix it in with a curve and got all three set right now. Just wish my radio said what the speeds were, case were i'm going to fly is roughing it, 300 miles away, no computer

I see a menu in the tx for governor, I put a post over at the jr board as well last night

Flew this thing yesterday and it is the bomb. Easy to setup, easier to fly. Liked it so much got another in route for my 693 electric

08-29-2010, 02:24 PM	#1 (permalink)
helipainter Registered Users Join Date: Sep 2009	programing 11x for gov OK, so i managed to get my totalg installed, got everything setup but i am at a loss as to why my Governor settings can't be easier to figure out, moreso with the 11x. Anybody know why my governor window in 11x is greyed out like not accesible? Right now i have some mixing to aux5 but it only gave me two gov settings and left idle1 with no gov. Did i skip something setting it up? I spooled her up and so far so good. It's a gasser so i was a little concerned Once i understood how to sett the G up, it was a walk in the park. I feel like i forgot something, but it is ready to go except this governor issue. Thanks for any ideas you guys got __________________ US Drones Aerial Media Pros Ritewing

08-29-2010, 04:12 PM	#2 (permalink)
ncarbon Registered Users Join Date: Jun 2010	11X and TotalG GOV I have my GOV on the GEAR channel controled by the FMOD switch so I have OFF 1650 and 1950. In system menu under devices you have to choose the channel setting , INH ACT GYO GOV, but any channel after AUX3 only has INH ACT option. So my GOV is set for GEAR channel and in DEVICE I havr GEAR set to GOV. Hope this helps. Ned

08-29-2010, 06:56 PM	#3 (permalink)
helipainter Registered Users Thread Starter Join Date: Sep 2009	That was what mine is setup like for the most part. So you have the gov off in norm, then it is on in idle1 and idle2? That makes since. I see the word governor in my menu for the 11x, what governor does that work with? I'd love to see real numbers so i could adjust if i needed to in the field. I fly 300 miles from a computer. Right now like this i gotta have the PC to see what speeds i'm hitting with what endpoints. __________________ US Drones Aerial Media Pros Ritewing

08-29-2010, 07:04 PM	#4 (permalink)
ncarbon Registered Users Join Date: Jun 2010	Can you get into the GOV menu I could tell you mine* the values and corresponding RPMs ? Ned

08-30-2010, 07:49 AM	#5 (permalink)
helipainter Registered Users Thread Starter Join Date: Sep 2009	yes, i can get into the totalG software and see the values as i adjust them. lastnight i was able to mix it in with a curve and got all three set right now. Just wish my radio said what the speeds were, case were i'm going to fly is roughing it, 300 miles away, no computer I see a menu in the tx for governor, I put a post over at the jr board as well last night Flew this thing yesterday and it is the bomb. Easy to setup, easier to fly. Liked it so much got another in route for my 693 electric __________________ US Drones Aerial Media Pros Ritewing

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in