Register Now

mahbouni · 07-10-2014, 03:14 AM

My Logo 600 has Rotortech 640 mains and Rail 106 tails, running 2250rpm on the head. I've been using the QuickUK tail unit but I want to put the latest Mikado tail unit on. Has anyone else run 2250rpm with 105mm or 106mm tails? did you have any issues?

bavci_0655 · 07-10-2014, 04:10 PM

I tried 2200RPM with KBDD 106mm tail blades. There was too much vibration with that setup.

Do you use SX rotor head with 640mm blades?

mahbouni · 07-10-2014, 05:23 PM

It's the latest 600SE rotor head. One piece but with longer main shaft

mahbouni · 07-24-2014, 05:50 PM

Just thought I would update on this. I fitted the latest Mikado tail rotor hub and grips. I've been flying it @ 2260rpm head speed with Rail 106mm tail blades. About 30 flights so far with no issues. It runs smoother than the QUK tail unit, which used to buzz a lot.

07-10-2014, 03:14 AM	#1 (permalink)
mahbouni Registered Users Join Date: Jan 2007	105mm tails @ 2250rpm head speed My Logo 600 has Rotortech 640 mains and Rail 106 tails, running 2250rpm on the head. I've been using the QuickUK tail unit but I want to put the latest Mikado tail unit on. Has anyone else run 2250rpm with 105mm or 106mm tails? did you have any issues? __________________ Oxy2 210 \| Oxy3 285 \| Oxy4 380 \| Logo 480XX \| 600SX \| 650SX \| 690SX \| 700 \| 700XX \| VControl

07-10-2014, 04:10 PM	#2 (permalink)
bavci_0655 Registered Users Join Date: Sep 2010	I tried 2200RPM with KBDD 106mm tail blades. There was too much vibration with that setup. Do you use SX rotor head with 640mm blades? __________________ LOGO 600 SX [ Pyro 700-52M \| Scorp. Commander V 130A OPTO \| VBar Neo \| BLS255HV & BLS256HV ] LOGO 600 SX [ HKII-4225-500KV \| Scorp. Commander V 130A OPTO \| VBar Neo \| BLS255HV & BLS256HV ]

07-10-2014, 05:23 PM	#3 (permalink)
mahbouni Registered Users Thread Starter Join Date: Jan 2007	It's the latest 600SE rotor head. One piece but with longer main shaft __________________ Oxy2 210 \| Oxy3 285 \| Oxy4 380 \| Logo 480XX \| 600SX \| 650SX \| 690SX \| 700 \| 700XX \| VControl

07-24-2014, 05:50 PM	#4 (permalink)
mahbouni Registered Users Thread Starter Join Date: Jan 2007	Just thought I would update on this. I fitted the latest Mikado tail rotor hub and grips. I've been flying it @ 2260rpm head speed with Rail 106mm tail blades. About 30 flights so far with no issues. It runs smoother than the QUK tail unit, which used to buzz a lot. __________________ Oxy2 210 \| Oxy3 285 \| Oxy4 380 \| Logo 480XX \| 600SX \| 650SX \| 690SX \| 700 \| 700XX \| VControl

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in