START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Skookum Robotics Skookum Robotics SK-360 SK-540 & SK-720 Digital Flybar |
|
LinkBack | Thread Tools | Display Modes |
05-06-2012, 04:14 AM | #1 (permalink) |
Registered Users
Join Date: Mar 2010
|
Outrage Torq BL9188 - Very rough
I am just finishing up a Trex 700E with the Custom Heli Parts Direct to Swash frames and Outrage Torq Servos all round. The cyclics are fine and see to be very fast, running off a 2S LiPo connected directly through the power bus. However, the BL9188 Tail servo is extremely rough and makes a lot of noise, as well as transmitting a lot of vibration down the carbon tail control rod. It is set up in the Skookum wizards as a custom servo, 333Hz, 760micro secs pulse width.
There was a post I found somewhere saying that this had been seen with V-Bar and that you should just fly with it like this - I can no longer locate that post, but I just don't feel comfortable with it the way it is. Any Ideas? Should I just send it back to HeliDirect where I got it? Even without the linkage connected it still feels rough/ratchety. I also found posts suggesting to increase the deadband slightly to quiet down the twitchiness when there is no input from the radio, but this had no effect. There is a video of Lukas Riva on you tube running these servos with a Velocity 90 and an SK720 so it doesn't look like there is any compatibility issues between the Skookum (except for the max frequency being only 333Hz instead of 560hz Any ideas? Thanks Davehttps://www.helifreak.com/images/smilies/BangHead.gif |
Sponsored Links | |||
Advertisement |
|
05-06-2012, 08:01 AM | #2 (permalink) |
Registered Users
|
Same setup here on a Furion 6.
Skookum, Outrage all around running a Western Robotics BEC at 8.4volts. 9188 is always chattering but I've decided to ignore it and just fly it anyway. Really doesn't seem to be a problem, flies real solid (sports flying).
__________________
Futaba 14SG, Synergy E5, Furion 6, Beam E4(v1) FBL, CGY750, Skookum |
05-06-2012, 08:50 AM | #3 (permalink) |
Registered Users
Join Date: Dec 2009
|
I've got the 9188. It is real rachetty on the ground with control input. But, it flies super smooth!
-g |
05-06-2012, 08:51 AM | #4 (permalink) |
Registered Users
Join Date: Apr 2010
|
Got 1 on both my 6 & 7hvs apart from the usual digi buzzing there very smooth
I'm running mine @ 8.4v too.
__________________
Oxy 3 SK540 Minijazz 20 / WARP 360 SK540 Koby 55 / Goblin 500 SK540 jive 100 / 6HV ultimate Helijive120 SK540 / 7HV SK540 Kosmik200 / Futaba18mz / Skookum support rep |
05-06-2012, 11:00 AM | #5 (permalink) |
Registered Users
|
I just installed mine (outrage 9188) yesterday that I received mine from helidirest. I flew my 550 yesterday and the day was spot on solid and handled everything I could throw at it. I checked it upon landing and it was still ratchity and noisy so I'm saying screw it, its fine and obviously just a noisy beast in nature.
__________________
john powers lcdr |
05-06-2012, 02:12 PM | #6 (permalink) |
Registered Users
Join Date: Aug 2009
|
My MKS DS-760 is "ratchety" too, but seems to fly fine. I thought it had something to do with DSMx and the "11ms/22ms, 1024/2048" thing?
Does this same thing happen with Futaba? |
05-06-2012, 02:58 PM | #7 (permalink) |
Registered Users
Thread Starter
Join Date: Mar 2010
|
I tried changing the receiver frequency between 1024 and 2048 but that made no difference. It is supposed to also be an issue with V-Bar. I am wondering if it has something to do with how the SK720 communicates with the servo during setup vs when it is flying due to the narrow pulse width of this servo. This is the first 760 servo I have used.
I just don't feel comfortable flying with the tail making this much grinding noise. The same tail and boom was on my regular 700E and had no issues (smooth as silk) and so it is not the tail slider or anything back there. I am going to try running this servo off my BeastX to see if that makes any difference and I will report back. Here is the thread where I originally saw this being a known issue, but have not been able to tract it down further in the V-bar thread yet. https://www.helifreak.com/showthread.php?t=389407 Dave |
05-06-2012, 03:03 PM | #8 (permalink) |
Registered Users
Join Date: May 2011
|
Just finished up a 6HV today and I'm getting the same grinding noise I'm curious to see what you find out.
AJ |
05-06-2012, 04:00 PM | #9 (permalink) |
Join Date: Mar 2007
|
=] its a high frequency servo, it makes a racket and is worse on a carbon boom, carbon push-rod etc,
__________________
|
05-06-2012, 05:19 PM | #10 (permalink) |
Registered Users
Thread Starter
Join Date: Mar 2010
|
Yep That is exactly the config I have, carbon (look alike anyhow) boom and Carbon tail control rod and it sounds absolutely horrible, I am going to try it tentatively in a simple hover as soon as I get the governor set up (Scorpion Commander V130A with phase sensor feeding the SK720).
I will report back - just hard to get used to the idea of flying a helicopter with this kind of grinding mechanical noise. All the reports though says that it flys awesome and very smooth. Dave |
05-06-2012, 05:30 PM | #11 (permalink) |
Join Date: Mar 2007
|
=] I think they fill them with sand??!
__________________
|
05-06-2012, 05:33 PM | #12 (permalink) |
Registered Users
|
The sand is what makes them so smooth in flight.
I'll tell ya though, its a strong servo!
__________________
Futaba 14SG, Synergy E5, Furion 6, Beam E4(v1) FBL, CGY750, Skookum |
05-06-2012, 05:40 PM | #13 (permalink) |
Join Date: Mar 2007
|
=] it's possibly the best servo you could own, without question!
__________________
|
05-06-2012, 10:35 PM | #14 (permalink) |
Registered Users
Thread Starter
Join Date: Mar 2010
|
Thats what all the reports say so I will bite the bullet and put it in the air in the next few days and let you all know how it goes. I am thinking of building a Goblin with these servos on it so this will be a much cheaper test bed to figure it all out. Hope to do the Beast X test tonight or tomorrow too.
Dave |
05-08-2012, 01:33 AM | #15 (permalink) |
Registered Users
Thread Starter
Join Date: Mar 2010
|
I just finished the test of the Outrage Torq BL9188 with my BeastX (actually an AR7200BX) which is on my stretched 450Pro. I just unplugged that tail servo, reprogrammed the AR7200BX to 760 micro secs pulse width and 560Hz frequency, and plugged in the BL9188.
The result is much smoother (not completely quiet) but definitely acceptable. So now the question - is it the frequency issue on the SK that is making this worse? Anyone know what frequency options the V-Bar offers as this grinding noise is supposed to be an issue on the V-Bar too. Art - What are the chances of getting a 560Hz option into the SK720 anytime soon? Now on to complete the 700E Direct to Swash project and see how the tail actually flies. Dave |
07-15-2012, 02:15 AM | #16 (permalink) |
Registered Users
|
So the settings for the Outrage servo 9188 is 333Hz, 760us and 0.04 running on 7.4v with the SK-540?
__________________
Kasama Srimok 90: JR8917HV all round | YS91SR | Hatori 946 | Spartan Quark | BLS251 http://nitro-magic.blogspot.com |
07-15-2012, 06:22 AM | #17 (permalink) |
Registered Users
Join Date: Feb 2011
Location: Australia
|
I have the same issue with the DS650, while connected to the PC the movement is terrible ( rough), once disconnected its better but still not what it should be.
While the vbar on my 550 with DS650 runs smooth, I hope the skookum wont cause premature failure...
__________________
Rapid Helis Australia |
07-15-2012, 09:39 AM | #18 (permalink) |
Registered Users
Join Date: Jul 2010
|
I must have about 50 flights now with the SK540 /ds650 and its working fine. I do ask a lot of the tail with my flying so i think it would have failed if the SK540 had issues.
|
Thread Tools | |
Display Modes | |
|
|