Compass Warp 360 Official Statement

[s0laris]

what about the plastic tail arm holder that attaches to the boom ?

I need a new one as I did not thread the bolt square..

[Jeff_Barrett]

If you contact the dealer you purchased from, Mike, they can get you looked after.

If you have problems getting the part from them, let me know and I'll look after you directly.

[s0laris]

k will do thx

[Jeff_Barrett]

Originally Posted by Dave Ketelhut

Distributors will be receiving these replacement parts by the end of February to send to current customers. Future Warp 360 kits will have the changes included.

Folks, we've been getting s lot of questions about when parts will be available.

I just want to point out again, that we will have availability at the end of February.

Thank you, everyone for your patience.




Sent from my SGH-I747M using Tapatalk 2

[itsmillertime0]

On the thicker tail booms is this a smaller i.d. or larger o.d.? If the former, is the tail case center a smaller o.d. as well?

[Caleb White]

Originally Posted by itsmillertime0

On the thicker tail booms is this a smaller i.d. or larger o.d.? If the former, is the tail case center a smaller o.d. as well?

Good question, I will try to find out. My guess is outer diameter change, or even if both change slightly, it will make little difference to part fitment of either end. .3 to .4mm is a small change. .4mm = 1/64"

[s0laris]

so ya apparently there are no replacement parts for the plastic tail holder. Mine is a slightly off bad mold.

I just have to be patient.. end of month is when we get the replacements and upgrades so i am sure by then I can pick up a new holder.

[Jeff_Barrett]

Originally Posted by s0laris

so ya apparently there are no replacement parts for the plastic tail holder. Mine is a slightly off bad mold.

I just have to be patient.. end of month is when we get the replacements and upgrades so i am sure by then I can pick up a new holder.

Mike, which part # do you need from the manual? We just received a whole bunch of Warp 360 parts yesterday and put them in the system.

[s0laris]

Part Number 10-2001 (Tail Arm Holder)

[Caleb White]

Originally Posted by Caleb White

Good question, I will try to find out. My guess is outer diameter change, or even if both change slightly, it will make little difference to part fitment of either end. .3 to .4mm is a small change. .4mm = 1/64"

the new tail OD changes, not the inside. doesn't affect other parts.

[s0laris]

if OD changes, then wouldn't that indeed affect other parts ?

[Jeff_Barrett]

Originally Posted by s0laris

Part Number 10-2001 (Tail Arm Holder)

Where did you purchase it from?

Flip me an email with your shipping address (I think we have it in the system) and I will take care of you if the dealer you purchased it from is unable to.

[radu7]

Originally Posted by s0laris

if OD changes, then wouldn't that indeed affect other parts ?

I think all that it would do would make the gap in the tail boom holder just a tiny amount wider than it is now when you clamp the boom in it. It may also make the tail control arm be a little closer to the boom (the part that some people have scratching their boom if they leave the link ball screw too long). I'm thinking the difference is so small that it would be hard to notice.

[s0laris]

I purchased it from RotorQuest. Shawn is going to take care of it he said.. so no worries.

Thanks for the offer Jeff

[Jeff_Barrett]

Excellent. Glad to hear it, Mike!

[Rob43]

Any updates on guide roller brace and motor can? I will have my new ESC in a week, and would like to get airbore soon after when weather allows. I'd rather wait for the brace than crash if I happen to have a belt issue. So far, in testing, mine appears to track nicely, but haven't loaded it up yet.

[s0laris]

i thought it was end of this month

[crf69]

i heard they are just waiting on all the parts to come in.

[Silverexpress01]

Can someone tell me if the off-the-shelf Compass 360 at Nankin Hobby Farmington had all the upgraded components? :-)

[Jeff_Barrett]

They likely won't yet, unless Mike received all the updates last week ... but when I spoke to him last week, they hadn't arrived yet.