Register Now

filtr · 10-05-2012, 12:01 AM

Hi Folks

I have worked all night long and could not get R7008SB to run. I have the SK SBUS wire contented. I have all the servo wires attached to the SK. I have the BEC contected to the SK at the IO B port it lights up the SK system. I have up load that it is a SBUS receiver. What else do I have to do to make it work.

Thanks

thefrog · 10-05-2012, 02:45 AM

what do you mean it's not working? Please explain in a bit more detail.

ModelGuard · 10-05-2012, 03:38 AM

If this is a 720 you have the Rx attached to the 720 with special lead? Try the other port next door.
If this is 540 then this should be connected to IO-B! with ordinary servo lead.
Is there power to the Rx? is the light on?
Have you bound the Rx to your radio?

ModelGuard · 10-05-2012, 03:51 AM

You have the sbus lead connected like the one on the left in the picture?

thefrog · 10-05-2012, 04:27 AM

Don't forget to use a power lead from the Rx to the SK (a servo lead with only + and -, no signal).

heathy · 10-05-2012, 04:56 AM

Yeah. As Frog just said you will need to run a lead like the Sk ones that go from Sk to power bus and take out the signal wire. This will now give enough power to the rx.

Sent from my iPhone 4s using tapatalk

ModelGuard · 10-05-2012, 05:28 AM

that wont stop the system working on the bench though, it just prevents brownouts

heathy · 10-05-2012, 06:44 AM

Mine did, when using the 720 with the s-bus adapter cable the rx wouldn't get a green light, instead i got a red/green flashing power warning. Used the lead without signal and all was well

ModelGuard · 10-05-2012, 07:01 AM

I take my comment back then!

heathy · 10-05-2012, 08:15 AM

It was something to do with the output voltage through the s-bus adapter lead being just under the futaba's required voltage. It was just under. Lucky the futaba Rx's are high voltage as i'm pumping 8.4v into mine..

filtr · 10-05-2012, 10:28 AM

Hi Folks

I have the SBUS going to the SK unit the way the photo shows. I have the power from BEC going the SK unit only. How should the power be getting to the RX. I have the SK power connected to the IO-B port only.

Thnaks

thefrog · 10-05-2012, 11:32 AM

Quote:

Originally Posted by filtr

Hi Folks

I have the SBUS going to the SK unit the way the photo shows. I have the power from BEC going the SK unit only. How should the power be getting to the RX. I have the SK power connected to the IO-B port only.

Thnaks

Take servo lead, remove the signal wire (white/orange) and plug one side of the remaining lead (with a + and - wire) an open port on the SK and the other into an open port/ power port in the Rx.

filtr · 10-05-2012, 11:39 AM

Thanks for the info I will give it a try.

georgi UK · 10-05-2012, 11:50 AM

=] yes an open port, but not the ex-led!

Arcturus97 · 10-05-2012, 07:32 PM

This thread has got me concerned. I've got an SK-540 connected to a 6208 SBUS rx. I've only got one cable going to that RX: the SBUS lead to IO-B. I'm running a 2S lipo into the SK540. No problems so far, 7 flights in.

How much power does the RX need? Why isn't one servo lead good enough? I'm missing something here...

filtr · 10-05-2012, 09:14 PM

As you can see the power is contented to the receiver. Then I contented a cable from the receiver to the SK unit for power. Then I contented the SBUS wire. When plug the power in the receiver works. Then I contented the power to the SK the red light stays on till i move the throttle up to full then it turns green but dose not pump

The servo start to chatter. When I move the sk unit it tries to move the servos that are contented.

What is the problem.

ModelGuard · 10-06-2012, 02:02 AM

Quote:

Originally Posted by Arcturus97

This thread has got me concerned. I've got an SK-540 connected to a 6208 SBUS rx. I've only got one cable going to that RX: the SBUS lead to IO-B. I'm running a 2S lipo into the SK540. No problems so far, 7 flights in.

How much power does the RX need? Why isn't one servo lead good enough? I'm missing something here...

You only need to worry if you are using the sk special sbus lead .you are using a servo lead you are fine

Sent from my GT-I9300 using Tapatalk 2

georgi UK · 10-06-2012, 03:52 AM

Quote:

Originally Posted by filtr

Then I contented the power to the SK the red light stays on till i move the throttle up to full then it turns green but dose not pump

What is the problem.

=] throttle reversed in the Tx?

heathy · 10-06-2012, 04:21 AM

Georgi got there 1st!

Ps. The lead that you've used to take power from a spare port to the rx should be plugged in all the time. It's only when you make your normal connection that it all becomes live.

Sent from my iPhone 4s using tapatalk

Arcturus97 · 10-06-2012, 04:42 AM

Quote:

Originally Posted by ModelGuard

You only need to worry if you are using the sk special sbus lead .you are using a servo lead you are fine

Sent from my GT-I9300 using Tapatalk 2

Got it, thanks

10-05-2012, 12:01 AM	#1 (permalink)
filtr Registered Users Join Date: Dec 2008	SBUS Issue Hi Folks I have worked all night long and could not get R7008SB to run. I have the SK SBUS wire contented. I have all the servo wires attached to the SK. I have the BEC contected to the SK at the IO B port it lights up the SK system. I have up load that it is a SBUS receiver. What else do I have to do to make it work. Thanks

10-05-2012, 03:38 AM	#3 (permalink)
ModelGuard Registered Users Join Date: Feb 2011	If this is a 720 you have the Rx attached to the 720 with special lead? Try the other port next door. If this is 540 then this should be connected to IO-B! with ordinary servo lead. Is there power to the Rx? is the light on? Have you bound the Rx to your radio? __________________ SimStream wireless from your transmitter to simulator http://www.modelguard.com

10-05-2012, 03:51 AM	#4 (permalink)
ModelGuard Registered Users Join Date: Feb 2011	You have the sbus lead connected like the one on the left in the picture? __________________ SimStream wireless from your transmitter to simulator http://www.modelguard.com

10-05-2012, 04:56 AM	#6 (permalink)
heathy Registered Users Join Date: Apr 2010	Yeah. As Frog just said you will need to run a lead like the Sk ones that go from Sk to power bus and take out the signal wire. This will now give enough power to the rx. Sent from my iPhone 4s using tapatalk __________________ Oxy 3 SK540 Minijazz 20 / WARP 360 SK540 Koby 55 / Goblin 500 SK540 jive 100 / 6HV ultimate Helijive120 SK540 / 7HV SK540 Kosmik200 / Futaba18mz / Skookum support rep

10-05-2012, 05:28 AM	#7 (permalink)
ModelGuard Registered Users Join Date: Feb 2011	that wont stop the system working on the bench though, it just prevents brownouts __________________ SimStream wireless from your transmitter to simulator http://www.modelguard.com

10-05-2012, 02:45 AM	#2 (permalink)
thefrog Registered Users Join Date: Feb 2011	what do you mean it's not working? Please explain in a bit more detail.

10-05-2012, 04:27 AM	#5 (permalink)
thefrog Registered Users Join Date: Feb 2011	Don't forget to use a power lead from the Rx to the SK (a servo lead with only + and -, no signal).

10-05-2012, 06:44 AM	#8 (permalink)
heathy Registered Users Join Date: Apr 2010	Mine did, when using the 720 with the s-bus adapter cable the rx wouldn't get a green light, instead i got a red/green flashing power warning. Used the lead without signal and all was well __________________ Oxy 3 SK540 Minijazz 20 / WARP 360 SK540 Koby 55 / Goblin 500 SK540 jive 100 / 6HV ultimate Helijive120 SK540 / 7HV SK540 Kosmik200 / Futaba18mz / Skookum support rep

10-05-2012, 07:01 AM	#9 (permalink)
ModelGuard Registered Users Join Date: Feb 2011	I take my comment back then! __________________ SimStream wireless from your transmitter to simulator http://www.modelguard.com

10-05-2012, 08:15 AM	#10 (permalink)
heathy Registered Users Join Date: Apr 2010	It was something to do with the output voltage through the s-bus adapter lead being just under the futaba's required voltage. It was just under. Lucky the futaba Rx's are high voltage as i'm pumping 8.4v into mine.. __________________ Oxy 3 SK540 Minijazz 20 / WARP 360 SK540 Koby 55 / Goblin 500 SK540 jive 100 / 6HV ultimate Helijive120 SK540 / 7HV SK540 Kosmik200 / Futaba18mz / Skookum support rep

10-05-2012, 10:28 AM	#11 (permalink)
filtr Registered Users Thread Starter Join Date: Dec 2008	Hi Folks I have the SBUS going to the SK unit the way the photo shows. I have the power from BEC going the SK unit only. How should the power be getting to the RX. I have the SK power connected to the IO-B port only. Thnaks

10-05-2012, 11:39 AM	#13 (permalink)
filtr Registered Users Thread Starter Join Date: Dec 2008	Thanks for the info I will give it a try.

10-05-2012, 11:50 AM	#14 (permalink)
georgi UK Join Date: Mar 2007	=] yes an open port, but not the ex-led! __________________

10-05-2012, 07:32 PM	#15 (permalink)
Arcturus97 Registered Users My HF Map location Join Date: Jan 2011	This thread has got me concerned. I've got an SK-540 connected to a 6208 SBUS rx. I've only got one cable going to that RX: the SBUS lead to IO-B. I'm running a 2S lipo into the SK540. No problems so far, 7 flights in. How much power does the RX need? Why isn't one servo lead good enough? I'm missing something here... __________________ * Goblin 700C, iKON, Torq 9180/9188, Quantum 4530-500, Edge HV160, Cyclone 695 * Outrage Fusion 50, SK-540, Torq 9180/9188, Quantum 4135-530, Edge HV80, SAB 630 Blk 3D * Align T-Rex 500E DFC, SK-540, ICE 75 * Futaba 14SG

10-05-2012, 09:14 PM	#16 (permalink)
filtr Registered Users Thread Starter Join Date: Dec 2008	As you can see the power is contented to the receiver. Then I contented a cable from the receiver to the SK unit for power. Then I contented the SBUS wire. When plug the power in the receiver works. Then I contented the power to the SK the red light stays on till i move the throttle up to full then it turns green but dose not pump The servo start to chatter. When I move the sk unit it tries to move the servos that are contented. What is the problem. Attached Thumbnails

10-06-2012, 04:21 AM	#19 (permalink)
heathy Registered Users Join Date: Apr 2010	Georgi got there 1st! Ps. The lead that you've used to take power from a spare port to the rx should be plugged in all the time. It's only when you make your normal connection that it all becomes live. Sent from my iPhone 4s using tapatalk __________________ Oxy 3 SK540 Minijazz 20 / WARP 360 SK540 Koby 55 / Goblin 500 SK540 jive 100 / 6HV ultimate Helijive120 SK540 / 7HV SK540 Kosmik200 / Futaba18mz / Skookum support rep

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in