START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Mikado Logo 700 Xxtreme Mikado Logo 700 Xxtreme Helicopters Discussion |
|
LinkBack | Thread Tools | Display Modes |
03-27-2010, 10:21 AM | #41 (permalink) |
Registered Users
Join Date: Jan 2007
|
You mean the slave connection must be buffered with a seperate battery or just connect both master and slave connections to power the rx in parallel?
__________________
Oxy2 210 | Oxy3 285 | Oxy4 380 | Logo 480XX | 600SX | 650SX | 690SX | 700 | 700XX | VControl |
Sponsored Links | |||
Advertisement |
|
03-27-2010, 05:00 PM | #42 (permalink) |
Registered Users
Join Date: Apr 2008
|
Its much better to use 2 cables with the jive and if you like also a buffer pack, or just set the BEC to 5.6V and there will be no problems.
I have TDR/MPXLE/Stretch logo all on 12S. |
03-27-2010, 06:22 PM | #43 (permalink) | |
Registered Users
Join Date: Jan 2007
|
Quote:
How do you wire up the buffer pack when using both cables to power the rx?
__________________
Oxy2 210 | Oxy3 285 | Oxy4 380 | Logo 480XX | 600SX | 650SX | 690SX | 700 | 700XX | VControl |
|
03-27-2010, 07:56 PM | #44 (permalink) |
Registered Users
Join Date: Apr 2008
|
Just plug a buffer pack into any spare channel in the RX.
The 5.6V is a good number because once you have savox or 8717 servos etc or high current draw servos the back emf created can be a higher voltage than its output and so the BEC circuit shuts off, kontronik released a statement about this.\ On 5.6V no problem, on 6V its a problem. Unless you run BLS servos then 6V is no drama. |
03-27-2010, 09:50 PM | #45 (permalink) | ||
Registered Users
Join Date: Oct 2008
|
Quote:
Quote:
BUT NOT ON THE AR7100/AR7100R RECEIVER! It will burn.
__________________
|
||
03-28-2010, 05:12 AM | #46 (permalink) | |
Registered Users
Join Date: Jan 2007
|
Quote:
__________________
Oxy2 210 | Oxy3 285 | Oxy4 380 | Logo 480XX | 600SX | 650SX | 690SX | 700 | 700XX | VControl |
|
03-28-2010, 05:16 AM | #47 (permalink) |
Registered Users
Join Date: Jan 2007
|
I have yet to buy the rx for my Logo 700. Which Spektrum rx would be best for 6V with Jive, master, slave + buffer pack? Which would be best for 2s lipo and HV servos?
__________________
Oxy2 210 | Oxy3 285 | Oxy4 380 | Logo 480XX | 600SX | 650SX | 690SX | 700 | 700XX | VControl |
03-28-2010, 06:25 AM | #48 (permalink) | |
Registered Users
Join Date: Oct 2008
|
Quote:
Jive, master, slave = No 2S lipo. An uregulated receiver. I donīt know if you can use a step down with lipo.
__________________
|
|
03-28-2010, 04:27 PM | #49 (permalink) | |
Registered Users
Join Date: Apr 2008
|
Quote:
It depends, if you want to use the BEC with no buffer pack its fine on 5.6V for 8717 etc or 6V for BLS servos. You will not notice a .4V drop in voltage, speed is not king with vbar so do not worry about that. If you want convenience use the internal BEC, if not use a buffer pack with it or a 2S lipo by itself. The way I see it adding a buffer pack with a BEC is like running one with a 2S lipo, anything can fail at any time. |
|
03-29-2010, 05:23 AM | #50 (permalink) |
Registered Users
Join Date: Dec 2008
|
As much as I like a chat, this topic is about the release date for the Logo 700. The last two pages are mostly covering BEC's.
I would like info on the release date please.
__________________
Regards, Jayson Logo 800Xx Silverline, Pyro 850-40L, Kosmik 200, 14S, 157 & 256 @ 8v Logo 400SE Silverline, Pyro 600-09, Jive 80+HV, 8S, 9660A+ 8900G @ 6v |
03-29-2010, 05:25 AM | #51 (permalink) |
Registered Users
Join Date: Apr 2008
|
2nd half of the year, there will be a german pilot flying the L700 at the 3DM, so until then we won't know much most likely
|
03-29-2010, 10:50 AM | #52 (permalink) | |
Registered Users
|
Quote:
Sorry right now there is no release date or ETA.
__________________
...Once upon a time there were Nitros, flybars & frequency pins...Shawn |
|
03-31-2010, 07:43 PM | #53 (permalink) |
Registered Users
Join Date: Jan 2008
|
maybe start a sticky on setup logo 700?
__________________
0utrage fusion 50, hk-4025 630kv scorpion.12s, v-bar, kontronik, Sponsored by hobbymaniac Proud to be a Maniac! |
03-31-2010, 08:26 PM | #54 (permalink) |
Registered Users
|
Not until gear ratios are known.
__________________
...Once upon a time there were Nitros, flybars & frequency pins...Shawn |
03-31-2010, 08:51 PM | #55 (permalink) |
Registered Users
Join Date: Sep 2007
|
Not to mention blade length, weight, battery compartment size and ... just about everything!
|
04-01-2010, 12:52 AM | #56 (permalink) |
Registered Users
|
Yup exactly, and HONESTLY I do not know anything of this model, I wish I did but it is all pretty hush hush on this one.
__________________
...Once upon a time there were Nitros, flybars & frequency pins...Shawn |
04-01-2010, 03:06 PM | #57 (permalink) |
Registered Users
|
The outline I got was that it will be huge, can take way more power than what's common, it's a 3D machine... and btw it will fly straight ahead too
Of course that doesn't say much... and I'm eager to see one in the air or better in my fleet -Klaus
__________________
SuziLAOS-DNHP-CenturioMax-Protos500-Logo400-500-600SE |
04-01-2010, 07:00 PM | #58 (permalink) |
Registered Users
Join Date: May 2004
Location: Northern Vermont
|
14s 5000 packs , hummm ! that would do it.
|
Thread Tools | |
Display Modes | |
|
|