START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Brand Specific Charger and Battery Support Brand Specific Charger and Battery Support |
|
LinkBack | Thread Tools | Display Modes |
11-11-2015, 12:58 AM | #1 (permalink) |
Registered Users
Join Date: Apr 2011
|
"Node over Amp" warning PL8
When I use my AGM battery as my power source for my PL8 I will get the warning message "Node over Amp push to reset" upon powering up the PL8 I do select battery as the power source, this warning will appear 90% of the time.
When I use my PL6 with my AGM battery as my power source I never get this warning... Is there something in the settings I need to change??
__________________
Revolectrix Ambassador Revolectrix.com 10% Discount All Products Code LEESS17 |
Sponsored Links | |||
Advertisement |
|
11-11-2015, 12:41 PM | #2 (permalink) |
Registered Users
|
Does the error occur when powered from a power supply?
__________________
Revolectrix Ambassador - Charger Specialist Revolectrix.com 10% discount for Batteries GCAM16 |
11-11-2015, 01:15 PM | #3 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2011
|
No only when powered by battery
__________________
Revolectrix Ambassador Revolectrix.com 10% Discount All Products Code LEESS17 |
11-11-2015, 02:15 PM | #4 (permalink) |
Registered Users
|
Are you using a car battery connected to a car that is running?
__________________
Revolectrix Ambassador - Charger Specialist Revolectrix.com 10% discount for Batteries GCAM16 |
11-11-2015, 02:32 PM | #5 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2011
|
No when the PL8 is connected to car battery, the car battery is not being charged so only the charger is connected to the battery.
when I'm finished I disconnect the PL8 and plug into the car charging system as it uses the same EC5 connector
__________________
Revolectrix Ambassador Revolectrix.com 10% Discount All Products Code LEESS17 |
11-11-2015, 04:11 PM | #6 (permalink) |
Registered Users
|
In firmware version 3.33 there was an adjustment to threshold for triggering the Node Over Current safety code. If you are not running 3.33, I would start there. If that does not resolve it, I would contact Revolectrix support.
__________________
Revolectrix Ambassador - Charger Specialist Revolectrix.com 10% discount for Batteries GCAM16 |
11-11-2015, 04:44 PM | #7 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2011
|
Just checked I'm running 3.32 will update to latest firmware
Hmmmm now how to update firmware??
__________________
Revolectrix Ambassador Revolectrix.com 10% Discount All Products Code LEESS17 |
11-11-2015, 04:56 PM | #8 (permalink) |
Registered Users
|
FUIM3 and the CCS. If you don't have a FUIM already, its highly recommended for any Powerlab owner. Really opens up the "lab" in Powerlab.
__________________
Revolectrix Ambassador - Charger Specialist Revolectrix.com 10% discount for Batteries GCAM16 |
11-11-2015, 06:47 PM | #9 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2011
|
Updated to 3.33 via the FUIM3 and all is working perfect!! thanks again Gregor99 really appreciate your time
__________________
Revolectrix Ambassador Revolectrix.com 10% Discount All Products Code LEESS17 |
Thread Tools | |
Display Modes | |
|
|