Register Now

threegs_00 · 07-26-2011, 12:12 PM

What screw size that will work to install my CP3 tail motor? Stock motor screws are too small.

dvdouden · 07-26-2011, 12:27 PM

Quote:

Originally Posted by threegs_00

What screw size that will work to install my CP3 tail motor? Stock motor screws are too small.

They come with the CP3 tail rotor... Don't know the size.

threegs_00 · 07-27-2011, 12:36 AM

Quote:

Originally Posted by dvdouden

They come with the CP3 tail rotor... Don't know the size.

Man I got jib

. None of my motor come with screws. One more thing to figure out. Its very hard to find these little bugger.

dvdouden · 07-27-2011, 02:23 AM

Quote:

Originally Posted by threegs_00

Man I got jib

. None of my motor come with screws. One more thing to figure out. Its very hard to find these little bugger.

The CP3-Screw Set (002381) probably has some of them. I can throw some in the mail for you (I have at least 3 unused sets of those screws that came with the rotor), but it'll take up to a week for them to arrive.

threegs_00 · 07-27-2011, 07:28 AM

Thanks man. I will try to check my local radio shack or LHS see if they have any. my extreme rotor should be here today.

threegs_00 · 07-27-2011, 07:33 AM

Anybody now if BladeSR tailmotor mount will fit in to the V2 Bee boom? I think its a good route away from the bee stock fin and motor mount if it does fit.

HELIHANKSTER · 07-27-2011, 11:41 AM

Quote:

Originally Posted by threegs_00

Anybody now if BladeSR tailmotor mount will fit in to the V2 Bee boom? I think its a good route away from the bee stock fin and motor mount if it does fit.

Yes, both the SR and Bee tail booms are 8mm, so the motor mount should work.

threegs_00 · 07-27-2011, 12:23 PM

Quote:

Originally Posted by HELIHANKSTER

Yes, both the SR and Bee tail booms are 8mm, so the motor mount should work.

cool man, thanks

threegs_00 · 07-27-2011, 12:32 PM

I think this will be my last post for this thread.

.Decided to go with Extreme rotor blade and or Blade SR rotor since they are both turn CW, will keep my CP3 TM turn the same way. Looks like I should be able to use servo horn screw on the TM (hopefully its not too long.Thanks for all the input and help

And this is what I have in the mail today..
.

07-27-2011, 12:32 PM	#50 (permalink)
threegs_00 Registered Users Thread Starter Join Date: Jul 2010	I think this will be my last post for this thread. .Decided to go with Extreme rotor blade and or Blade SR rotor since they are both turn CW, will keep my CP3 TM turn the same way. Looks like I should be able to use servo horn screw on the TM (hopefully its not too long.Thanks for all the input and helpAnd this is what I have in the mail today.. .

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-23-2011, 03:38 PM	#41 (permalink)
threegs_00 Registered Users Thread Starter Join Date: Jul 2010

07-26-2011, 12:12 PM	#42 (permalink)
threegs_00 Registered Users Thread Starter Join Date: Jul 2010	What screw size that will work to install my CP3 tail motor? Stock motor screws are too small.

07-27-2011, 07:28 AM	#46 (permalink)
threegs_00 Registered Users Thread Starter Join Date: Jul 2010	Thanks man. I will try to check my local radio shack or LHS see if they have any. my extreme rotor should be here today.

07-27-2011, 07:33 AM	#47 (permalink)
threegs_00 Registered Users Thread Starter Join Date: Jul 2010	Anybody now if BladeSR tailmotor mount will fit in to the V2 Bee boom? I think its a good route away from the bee stock fin and motor mount if it does fit.

Register Now

Log-in