START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Beam Beam Helicopters Factory Support Forum |
|
LinkBack | Thread Tools | Display Modes |
07-04-2012, 07:40 PM | #1 (permalink) |
Registered Users
Join Date: Dec 2007
|
avantgarde needs more pinions sizes
i really need a 14t pinion to make the head speed i want using a cc80hv gov.. will a logo pinion mesh with the avantgarde gear?? i wish beam would make a 14t and 15t pinion...
|
Sponsored Links | |||
Advertisement |
|
07-04-2012, 08:05 PM | #2 (permalink) |
Registered Users
Join Date: Mar 2008
|
Yeah that is a bit weird, 12t, 13t then straight to 16t?
It just limits your motor KV choices I guess.
__________________
Team Old Mate - He's a good bloke |
07-05-2012, 06:20 AM | #3 (permalink) |
Registered Users
Thread Starter
Join Date: Dec 2007
|
pinion
true ,but i only had a 600mx and a 700mx motor.
|
07-05-2012, 02:50 PM | #4 (permalink) |
Registered Users
Join Date: Dec 2011
|
Will the 700mx motor fit?
__________________
. Futaba 16SZH, Trex 700X, MicroBeast Plus, , POWER LAB 6 |
07-05-2012, 04:04 PM | #5 (permalink) |
Registered Users
Thread Starter
Join Date: Dec 2007
|
motor
hi. i think itwill fit if u dremel the frames towards the gear side. about an 1/8.. i went with the 600mx first because i wasnt sure of the balance points yet.. it maybe too nose heavy with the 700mx depending on lipos used .. can always use stick on weight on the tail to campensate,,,,,UPDATE---700mx fits with out mods .expect needing to drill motor mount to make the 4mm bolts fit
Last edited by audio131; 07-18-2012 at 07:25 AM.. |
07-18-2012, 07:24 AM | #6 (permalink) |
Registered Users
Thread Starter
Join Date: Dec 2007
|
still need pinions
really need a 14t pinion for the avantgarde,,beam please make one
|
07-26-2012, 12:15 PM | #7 (permalink) | |
Registered Users
Join Date: Dec 2011
|
Quote:
Sorry for the many questions, I guess without not seeing it I dont undersand how you drill the motor mount the make the 4mm bolts fit? Could you please give a little more detail? What pinion are you using with the 700mx?
__________________
. Futaba 16SZH, Trex 700X, MicroBeast Plus, , POWER LAB 6 |
|
07-26-2012, 03:51 PM | #8 (permalink) |
Registered Users
Thread Starter
Join Date: Dec 2007
|
motor mount
that motor mount was made for a 600 sized motor which the bolt pattern uses a 3mm bolt,, 700mx motor uses 4mm bolts to attach to a mount,, so just drill out the mount till u get the 4mm bolts to go thru it and into the 700mx motor.... used the stock 12t pinion..flat line throttle curve. the pinion is no high enough to run cc gov,. rreally a 14t is needed..
|
07-28-2012, 09:07 PM | #9 (permalink) |
Registered Users
Join Date: Dec 2011
|
Will cc ice 2 80 hv handle 700 bx
__________________
. Futaba 16SZH, Trex 700X, MicroBeast Plus, , POWER LAB 6 |
Thread Tools | |
Display Modes | |
|
|