Register Now

Ollie NL · 03-12-2010, 04:38 PM

Hi,

Recently received my Aurora 9.

I have some "problems" setting up my Gyro's (Futaba 401 and Spartan).

any one (Mike??) able to give some instructions on setting up Gyro's?
especially refering to Gain-settings

regards

Ollie
netherlands

iAdam · 03-13-2010, 11:24 AM

what seems to be the problem?

Ollie NL · 03-16-2010, 03:28 PM

Hi,

thank you for your reply.

In the meanwhile i've done some testing.

conclusion, had choicen the wrong setting in my transmitter.

It's rather simple to program the gyro (dual setting, assign a switch (rate/hold mode)) and off you go.

regards,

ollie Nl

jauguston · 03-23-2010, 06:38 PM

I just set mine up and used the left slider until I figure out how much gain works then I will assign a switch.

I also decided the switch behind the idle-up switch was not a good place for me to have the throttle hold. I was fooling around with it in my lap (EXI 450) in my motorhome and went to move the idle-up switch and my big finger bumped the throttle hold off and I had a lap full of wildcat. I moved it to the right side. I am now repairing the stripped main gear the Scorpion 2221-8 tore apart while I was trying to stop the chaos!!

Live and learn.

Jim

pgfc · 08-19-2014, 04:20 AM

Hi there,

Currently I have a problem with configuration of my heli.

I am a very begginer in the heli world, however I have my heli all set up (T-rex 450 V2 sport combo + Aurora 9X) just one problem with the gyro.

The servo responsible for the rear rotor works perfectly when connected directly to the receiver, however if I connect it through the gyro it does not work.

I configured gyro correctly (blinking LEDs), however it does not run the rear rotor.

May I ask you for some tips in this case?

03-12-2010, 04:38 PM	#1 (permalink)
Ollie NL Registered Users Join Date: Mar 2008	Gyro Set-up Hitec Aurora 9 Hi, Recently received my Aurora 9. I have some "problems" setting up my Gyro's (Futaba 401 and Spartan). any one (Mike??) able to give some instructions on setting up Gyro's? especially refering to Gain-settings regards Ollie netherlands

03-13-2010, 11:24 AM	#2 (permalink)
iAdam Registered Users Join Date: Sep 2008	what seems to be the problem? __________________ Protos 3dHS ThunderPower Motrolfly

03-16-2010, 03:28 PM	#3 (permalink)
Ollie NL Registered Users Thread Starter Join Date: Mar 2008	gyro setup Hi, thank you for your reply. In the meanwhile i've done some testing. conclusion, had choicen the wrong setting in my transmitter. It's rather simple to program the gyro (dual setting, assign a switch (rate/hold mode)) and off you go. regards, ollie Nl

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-23-2010, 06:38 PM	#4 (permalink)
jauguston Registered Users Join Date: Jan 2010	I just set mine up and used the left slider until I figure out how much gain works then I will assign a switch. I also decided the switch behind the idle-up switch was not a good place for me to have the throttle hold. I was fooling around with it in my lap (EXI 450) in my motorhome and went to move the idle-up switch and my big finger bumped the throttle hold off and I had a lap full of wildcat. I moved it to the right side. I am now repairing the stripped main gear the Scorpion 2221-8 tore apart while I was trying to stop the chaos!! Live and learn. Jim

08-19-2014, 04:20 AM	#5 (permalink)
pgfc Registered Users Join Date: Aug 2014	Hi there, Currently I have a problem with configuration of my heli. I am a very begginer in the heli world, however I have my heli all set up (T-rex 450 V2 sport combo + Aurora 9X) just one problem with the gyro. The servo responsible for the rear rotor works perfectly when connected directly to the receiver, however if I connect it through the gyro it does not work. I configured gyro correctly (blinking LEDs), however it does not run the rear rotor. May I ask you for some tips in this case?

Register Now

Log-in