PART SWAP THREAD!

[prototype3a]

I have a bunch of spare c-clips.

[maarset]

You can usually get them at home depot. On one of my logos I used a 'E-Clip'. Similar to a circlip. Can't remember which size I got.

http://www.circlips.com.au/contentbl...ips&sec3=d1500

[esmoglo]

Was looking for the plastic screws for the landing gear RH had them but no longer can anyone point me in the correct direction? Don't want snap my frames in a crash simple enugh really the plastic screws.

[prototype3a]

http://www.microfasteners.com/home.php?cat=776 IIRC they're M3 but I forget what length.

[jakeg1999]

Originally Posted by esmoglo

Was looking for the plastic screws for the landing gear RH had them but no longer can anyone point me in the correct direction? Don't want snap my frames in a crash simple enugh really the plastic screws.

I ordered some from amazon a couple years back, can't remember the details, but I'll take a look. I think they were a couple bucks and I got a hundred or so. They have a little bigger head for a blade tip screwdriver and a thumbscrew. I like them quite a bit more and they don't strip nearly as easy. They are about 2mm too long but a razor blade takes care of that instantly. You could also just pm me your address and I can send you a couple sets......Jake

[esmoglo]

Originally Posted by prototype3a

http://www.microfasteners.com/home.php?cat=776 IIRC they're M3 but I forget what length.

Thanks for the link! Stock ones are M3X10...

Originally Posted by jakeg1999

I ordered some from amazon a couple years back, can't remember the details, but I'll take a look. I think they were a couple bucks and I got a hundred or so. They have a little bigger head for a blade tip screwdriver and a thumbscrew. I like them quite a bit more and they don't strip nearly as easy. They are about 2mm too long but a razor blade takes care of that instantly. You could also just pm me your address and I can send you a couple sets......Jake

Jake PM sent!

[cougartrx]

Hello guys Does anyone have a spare swash driver,part # 4018.
Thanks

[jakeg1999]

Looking for a 15T Mod 1 pinion.

[cuheli]

Im looking for a Left side frame for a Logo 600/500. I had one on order but readyheli is done

[maarset]

Threw a belt off the front left pulley on my logo 500. Anyone please have an extra left side frame?

Would really appreciate it greatly!

Thanks
Mike

[maarset]

Originally Posted by maarset

Threw a belt off the front left pulley on my logo 500. Anyone please have an extra left side frame?

Would really appreciate it greatly!

Thanks
Mike

I'll pay full price plus shipping.
And a Starbucks Gift Card!
I'm really desperate here.

[maarset]

Well I was able to fix the frame and the heli seems fine now. SO don't need one. But if someone has one for my Pal Haas (cuheli) that would be cool.

Mike

[Roadracerr]

Have an unused 600 boom and belt to swap for same for 600 SE

[maarset]

Originally Posted by maarset

Looking for a 11T MOD 1.0 (NOT SX) Herringbone Pinion for a 6mm shaft.
If you have one please PM me.

Thanks so much

Mike in California

Found!

[freakinnovice]

Does anyone happen to have a18 tooth Mod .7 pinion for a 5mm motor shaft?

[dobis77]

Does anyone have a mod 1 106 tooth pinion for my logo 600? I have many parts I can trade for it or just buy it outright. Thanks!

[dobis77]

I just realized I said "106 tooth pinion". Lol. Main gear. Anyone

[prototype3a]

Heh. I was wondering...

[rando]

I need a 500/600 tail drive pulley pin, gear driver with pin, complete tail lever and metal lever holder, complete tail control ring, main shaft, main grip 3mm balls and 14mm cone washers, right side frame, single white landing bow and/or a pair of landing bows. I have quite a few 500/600 3D/SE/SX parts on hand I can offer in trade. Let me know what you have and what you're looking for.

[fazy]

Hey guys parting out my logo and wanted to let you guys know, just in case you guys need anything first. I have taken photos of a lot of parts that Im getting rid of Its a mix of logo 500/500se/600 parts but mostly 500se/500 stuff. What you see is what you get plus a few extra nuts bolts, booms, and a couple other goodies. Everything you see packaged is sealed from factory except one of the main shafts, the pack is open. All these parts are well over $300. I am asking for $200 paypal shipped for the lower 48. If you have any question feel free to ask. Please let me know if you need detailed listing of the parts but i think the pictures are pretty clear and have close ups of the part numbers. I will only keep the tail blades pictured on that tail now. Thanks guys