START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Mikado V-BAR Mikado V-Stabi/V-BAR Flybarless System Software and Hardware Support |
|
LinkBack | Thread Tools | Display Modes |
07-24-2014, 08:49 PM | #1 (permalink) |
Registered Users
Join Date: Sep 2011
|
Vbar 6 to 5.3
Can the software be downgraded? It is my understanding that 6.0 will work without control but not yet.
__________________
logo 600sx, 480, vcontrol ..mcpsbl Last edited by Dsss; 07-25-2014 at 07:45 AM.. |
Sponsored Links | |||
Advertisement |
|
07-24-2014, 09:48 PM | #2 (permalink) |
Registered Users
|
Yes there is a method for V6 to revert back to 5.3. Currently V6 is only for Vcontrol.
__________________
Wayne Logo 480 / Logo 600sx / Logo 690 / Logo 700 / Vbar Control |
07-24-2014, 09:53 PM | #3 (permalink) |
Registered Users
Thread Starter
Join Date: Sep 2011
|
Thank you sir. What is this method?
__________________
logo 600sx, 480, vcontrol ..mcpsbl |
07-24-2014, 10:58 PM | #4 (permalink) |
Registered Users
|
You would use the same Vbar recovery procedure you use to recover from a bad flash.
You need to load the recovery file into the VBAR from the VBAR page with your the VBAR PC software -> http://www.vstabi.info/en/node/397 . After you load this file into the VBAR, you can load the VBAR version 5.x as the normal version Which one you had before over the PC software to run VBAR with the normal TX.
__________________
Wayne Logo 480 / Logo 600sx / Logo 690 / Logo 700 / Vbar Control |
07-25-2014, 02:53 AM | #5 (permalink) | |
Registered Users
Join Date: Sep 2010
|
Quote:
The usb stopped working at version 6. Freddie |
|
07-25-2014, 04:42 AM | #6 (permalink) |
Registered Users
|
Just connect the vbar to the PC as normal, load up the VStabi software, the USB in in top bar will be green but it will say no connection in red next to it which is fine.
Then click on file then Firmware Upload, locate the recovery file then it should start to load it to your vbar, if it doesn't start within 20 seconds or so just unplug the power to the vbar and plug it in again. I have done this a few times but it doesn't always start to upload the file to the vbar , unplugging the vbar from the battery then plugging it in again will start the update.
__________________
Velos 880 Neo, Logo 800 XX Vbar, T-Rex 800 Pro DFC Vbar, T-Rex 800 Trekker Vbar, T-Rex 700 Pro DFC Vbar, T-Rex 800 F3C Vbar, T-Rex 550E DFC Vbar, T-Rex 500 Pro DFC AR7200BX, T-Rex 450 Sport V2 AR7200BX, T-Rex 250 Pro AR7200BX, VController, DX9. |
07-29-2014, 09:17 PM | #7 (permalink) |
Registered Users
Thread Starter
Join Date: Sep 2011
|
Thank you Wayne and John. I was just wondering.. when i switch to 6 from 5.x , will i need to pay for 6 without owing the v control?
__________________
logo 600sx, 480, vcontrol ..mcpsbl |
07-30-2014, 05:23 AM | #8 (permalink) |
Registered Users
|
If you don't own the VController then v6 is not available as an update as it only works with the VController.
Once you have purchased the controller then v6 is a free update plus it has the full pro functionality.
__________________
Velos 880 Neo, Logo 800 XX Vbar, T-Rex 800 Pro DFC Vbar, T-Rex 800 Trekker Vbar, T-Rex 700 Pro DFC Vbar, T-Rex 800 F3C Vbar, T-Rex 550E DFC Vbar, T-Rex 500 Pro DFC AR7200BX, T-Rex 450 Sport V2 AR7200BX, T-Rex 250 Pro AR7200BX, VController, DX9. |
07-30-2014, 03:00 PM | #9 (permalink) |
Registered Users
Thread Starter
Join Date: Sep 2011
|
Thank you and I understand that, but buying /owning a vbar with a "pro" version. Which will work with other transmitters eventually. Now downgrading to a non pro 5.3 and having to buy pro again, it seems there might be a better way to do this.
|
07-30-2014, 09:08 PM | #10 (permalink) |
Registered Users
|
So you are buying a used Vbar that someone already put 6.0 on?
__________________
Trex 700 Pro DFC - Compass 6HV - Vcontrol - Neo #nodroneshere - 104 |
07-30-2014, 09:37 PM | #11 (permalink) |
Registered Users
Thread Starter
Join Date: Sep 2011
|
I have a vbar silver with the vbar control sat combo with 6.0 installed. I am a few months out from getting a vcontrol. Maybe more with the holidays.
__________________
logo 600sx, 480, vcontrol ..mcpsbl |
07-31-2014, 12:41 AM | #12 (permalink) |
Registered Users
Join Date: Dec 2010
|
vbar silver line with express on it is $300
the silver line with the the RX is $360. an RX is $80.so buy them together and save $20. they didn't charge you for pro. 6.0pro is free, 5.3 pro is not.
__________________
Greg MSH USA Heli Flight Team Mikado V Team Lynx |
Thread Tools | |
Display Modes | |
|
|