Register Now

heli-cuzz · 06-14-2010, 08:40 AM

Ohh so smooth. The TZ90 NOBAR style is much better than expected. I was running the new YS91 excessively rich and I'm guessing the head speed was around 1600rpm.
Even with a sluggish over rich running engine. The collective and cyclic response was crisp fast and accurate. All my stick movements were minimal.
The climbouts were very quick with the heli rocketing upwards. A few aileron and elevator rocking movements with less than half stick input applied. The movements were lightning fast and snappy just like my NOBAR50
Hovering was a cakewalk with minimal input to keep it still. Even showed badbrad and a few others that it will hover thumbs off no better or no worse than its flybarred counterpart.
Flybars are not for me anymore. There are no regrets with removing the flybar.
FF and semi FFF circuits. The heli tracks and flies beautiful. Flies like its on rails!
Now its time to tune the YS to its potential. Burned almost 1 gallon so the break-in is just about done.
I'll give a thorough going over the machine this week and then its time to start hammering the NOBAR 90 like it wants me to.

heli-cuzz · 06-15-2010, 06:31 AM

Here's my set-up as is with 140 degree ccpm mix.

Engine and muffler: YS91st with an Outrage exhaust.
Limiter: RevMax with backplate sensor
Cyclic servos: JR 8917HV
Throttle servo: Futaba 9252
Tail servo: Futaba BLS251
Tail gyro: Futaba GY601
Regulator: SGP ReactorX2
Battery: ThunderPower 4600 2s2p
Main blades: Vblades 710
Tail blades: NO name carbon fiber 105
RX: Spektrum AR7100
TX: JRx9303
Fuel: CoolPower 30%
Glo-plug: OS #8
Can-O-Pee: Heli-Canz

kevinator9 · 07-09-2010, 02:19 PM

Very very nice Cuzz! Hope it flies as nice as your caliber

wacojoe · 07-25-2010, 09:47 PM

Please get some video of that machine flying!! Would love to see it.

heli-cuzz · 07-26-2010, 05:29 PM

Some stills from the make-a-wish event I flew at recently.

vid to come soon.

kevinator9 · 07-27-2010, 02:59 AM

Love the photo of the SHINY muffler!

06-14-2010, 08:40 AM	#1 (permalink)
heli-cuzz Registered Users My HF Map location Join Date: Dec 2005	NOBAR TZ90 maiden flight Ohh so smooth. The TZ90 NOBAR style is much better than expected. I was running the new YS91 excessively rich and I'm guessing the head speed was around 1600rpm. Even with a sluggish over rich running engine. The collective and cyclic response was crisp fast and accurate. All my stick movements were minimal. The climbouts were very quick with the heli rocketing upwards. A few aileron and elevator rocking movements with less than half stick input applied. The movements were lightning fast and snappy just like my NOBAR50 Hovering was a cakewalk with minimal input to keep it still. Even showed badbrad and a few others that it will hover thumbs off no better or no worse than its flybarred counterpart. Flybars are not for me anymore. There are no regrets with removing the flybar. FF and semi FFF circuits. The heli tracks and flies beautiful. Flies like its on rails! Now its time to tune the YS to its potential. Burned almost 1 gallon so the break-in is just about done. I'll give a thorough going over the machine this week and then its time to start hammering the NOBAR 90 like it wants me to. __________________ *Fury55 NIB Furion6 CGY750 fbl helicopter-Frenzy CGY750 fbl nitro-Frenzy fbl NOBAR90 and a clone450NOBAR* Burning Nitro and Electrons simultaneously

06-15-2010, 06:31 AM	#2 (permalink)
heli-cuzz Registered Users Thread Starter My HF Map location Join Date: Dec 2005	Here's my set-up as is with 140 degree ccpm mix. Engine and muffler: YS91st with an Outrage exhaust. Limiter: RevMax with backplate sensor Cyclic servos: JR 8917HV Throttle servo: Futaba 9252 Tail servo: Futaba BLS251 Tail gyro: Futaba GY601 Regulator: SGP ReactorX2 Battery: ThunderPower 4600 2s2p Main blades: Vblades 710 Tail blades: NO name carbon fiber 105 RX: Spektrum AR7100 TX: JRx9303 Fuel: CoolPower 30% Glo-plug: OS #8 Can-O-Pee: Heli-Canz __________________ *Fury55 NIB Furion6 CGY750 fbl helicopter-Frenzy CGY750 fbl nitro-Frenzy fbl NOBAR90 and a clone450NOBAR* Burning Nitro and Electrons simultaneously Last edited by heli-cuzz; 07-22-2010 at 10:42 AM..

07-09-2010, 02:19 PM	#3 (permalink)
kevinator9 Registered Users My HF Map location Join Date: Feb 2007 Location: Rolleston, Canterbury, New Zealand	Very very nice Cuzz! Hope it flies as nice as your caliber __________________ Andrew

07-26-2010, 05:29 PM	#5 (permalink)
heli-cuzz Registered Users Thread Starter My HF Map location Join Date: Dec 2005	Some stills from the make-a-wish event I flew at recently. vid to come soon. __________________ *Fury55 NIB Furion6 CGY750 fbl helicopter-Frenzy CGY750 fbl nitro-Frenzy fbl NOBAR90 and a clone450NOBAR* Burning Nitro and Electrons simultaneously

07-27-2010, 02:59 AM	#6 (permalink)
kevinator9 Registered Users My HF Map location Join Date: Feb 2007 Location: Rolleston, Canterbury, New Zealand	Love the photo of the SHINY muffler! __________________ Andrew

07-25-2010, 09:47 PM	#4 (permalink)
wacojoe Registered Users Join Date: Jun 2006	Please get some video of that machine flying!! Would love to see it.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in