Register Now

madsilencerr · 11-11-2014, 12:57 PM

Hello!After a crash last week, I just repaired my nano. So I powered it up, and the blue led started flashing.

So, I though it would need a rebind. After that, I am following all the instructions for binding with non computerised transmitter of the manual and it won't bind at all! The blue led just flashes!

I can't see any obvious damage to the board and the crash was not that bad anyway... what's going on?

madsilencerr · 11-11-2014, 01:12 PM

I really really hope I don't have to replace the board because it's totally out of stock here

nickyd · 11-11-2014, 10:06 PM

On my nano, I somtimes have to disconnect/reconnect the battery 4 or 5 times before I get a solid blue light. Worth a try.

madsilencerr · 11-11-2014, 11:14 PM

Hmm I have already done that unfortunately.... [emoji20]

Neunerball · 11-12-2014, 04:12 PM

Instead of getting a new board, I got a new Nanno, which also gives me lots of spare parts.

Flexin · 11-17-2014, 07:04 AM

I had something happen where my nano was looking for a computer transmitter instead of my dx4 and would not bind. Had to switch the nano back and everything worked fine.

lahannsven · 11-19-2014, 02:44 AM

Keep a distance of 3m. Sometimes when your heli is too close to the transmitter it doesn't bind.

Sven

11-11-2014, 12:57 PM	#1 (permalink)
madsilencerr Registered Users Join Date: Dec 2013	Nano will not bind to Dx4e Hello!After a crash last week, I just repaired my nano. So I powered it up, and the blue led started flashing. So, I though it would need a rebind. After that, I am following all the instructions for binding with non computerised transmitter of the manual and it won't bind at all! The blue led just flashes! I can't see any obvious damage to the board and the crash was not that bad anyway... what's going on?

11-11-2014, 10:06 PM	#3 (permalink)
nickyd Registered Users Join Date: Feb 2010	On my nano, I somtimes have to disconnect/reconnect the battery 4 or 5 times before I get a solid blue light. Worth a try. __________________ Nick Flying your heli the world is still out there, but at least for the time it hasn't got you by the throat. Mini Titan E325 FBL, Blade Nano Cpx

11-12-2014, 04:12 PM	#5 (permalink)
Neunerball Registered Users Join Date: Dec 2012	Instead of getting a new board, I got a new Nanno, which also gives me lots of spare parts. __________________ "Nothing is as constant as changes" DX9, DX6i, Blade Nano CP X, ZYX "Blade" 130X, Blade 180 CFX, Blade 230S, Blade 300X, Blade 450 3D (about 2 b FBL; have the parts, not the time), Blade 180QX, Blade 230S V2, Convergence, Mini Convergence.

11-17-2014, 07:04 AM	#6 (permalink)
Flexin Registered Users Join Date: Jun 2014	I had something happen where my nano was looking for a computer transmitter instead of my dx4 and would not bind. Had to switch the nano back and everything worked fine. __________________ Blade 300CFX, 180 CFX, Nano CPX (2), Nano QX (Micro-Motors), 200QX, RED BULL 130, 350QX, 350QX2AP, Latrax Alias, Camera, Light Bar DX9 and DX4e, Traxxas Slash 4X4

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-11-2014, 01:12 PM	#2 (permalink)
madsilencerr Registered Users Thread Starter Join Date: Dec 2013	I really really hope I don't have to replace the board because it's totally out of stock here

11-11-2014, 11:14 PM	#4 (permalink)
madsilencerr Registered Users Thread Starter Join Date: Dec 2013	Hmm I have already done that unfortunately.... [emoji20]

11-19-2014, 02:44 AM	#7 (permalink)
lahannsven Registered Users Join Date: Feb 2014 Location: Luxembourg	Keep a distance of 3m. Sometimes when your heli is too close to the transmitter it doesn't bind. Sven

Register Now

Log-in