720 Setup Files

[Finless]

Per a request by Skint Eastwood, here is a sticky for you all to post 720 setup files.

Below are links to posts that already have some setup files.

https://www.helifreak.com/showthread.php?t=221969
https://www.helifreak.com/showthread.php?t=215330
https://www.helifreak.com/showthread.php?t=209860

Bob

[Silverexpress01]

being updated

Coaxial setup example:
To be added..




Default values:
For reference...see attached

[RoToR ChAoS]

heres one from my 450 Hybread (work in progress)

[Cirkus]

It's not a setup FILE, but it may help someone setting up for the first time. Be advised this is how my own setup is, and it is an unregulated 7.4 "HV" setup. I think that's important to note.

________________________________________

lipo polarity is incorrect, please observe,

georgi UK

[georgi UK]

=] lipo polarity is incorrect, please observe,

georgi UK

[oldschool269]

Trex 700e
5.7v reg !!! , i am finding that the voltage needs to be stable .. needs to be !!
451 bls 3rd hole out , star horns
torq tail 3rd hole out star horn
hs 2200 st2 1950 st1
bell cranks set to high range (long throws)
Align 690 d mains , align CF TAIL BLADES
+- 12 deg collective
+- 10 deg cyclic

version 2.04 firmware

enjoy
hot dog 3d setup .. tail gain may be a click or two high



rename the file download as .sk7 ... not .zip
.zip is just to post it up on server here ..
jason

[georgi UK]

Originally Posted by Cirkus

It's not a setup FILE, but it may help someone setting up for the first time. Be advised this is how my own setup is, and it is an unregulated 7.4 "HV" setup. I think that's important to note.

=] awaiting updated lipo polarity corrections, RED / BLACK.

georgi UK

[Cirkus]

Originally Posted by gmcallister

=] awaiting updated lipo polarity corrections, RED / BLACK.

georgi UK

Note to potential diagram users:

I mislabeled the colors on the battery wires. Use common sense and don't plug your batteries in backwards. If you put your EC5 and EC3 connectors on properly, you can't plug them in wrong anyways. Also please note that I miscolored the servo leads, but I figured you would manage to figure that out too. In addition, if you do not use the same brand of HV servo or tail servo or regulator, you will of course swap those out and use your particular brand of device in it's place. Batteries shown are not to scale. Apparently if I don't mention things like that, certain people will not be able to figure out how this junk gets put together and it will all be my fault.

Georgi, get off my nuts.

[hjscm]

well thanks for that but a little too late. i followed your diagram and was really confused how you got it to work without any servo wheels on the swash servos. it has been driving me nuts. next time please put them on so i know. you did on the 251.

[Cirkus]

Originally Posted by hjscm

well thanks for that but a little too late. i followed your diagram and was really confused how you got it to work without any servo wheels on the swash servos. it has been driving me nuts. next time please put them on so i know. you did on the 251.

My bad. You got me there.

[Tisondm]

Here's the setup file on my Trex 600 with Version 2.04

CHP TREX 600 Esp FBL, SK720, 8S, Scorpion 4025-740, 19T, CC Ice 100, WR Bec

I started out with 50% cyclic gain and 40% tail gain. It's flying awesome with these settings so I don't plan on changing them. The setup file was saved after 4 flights with self tune bell gains on. I started out with the Basic 3D setup. I hope this helps.

Governed HS 2100
+/-11 Collective
10% Cyclic

[rickywu]

How can i upload my file here??

[alexf1852]

MSH Protos FBL - Jive 60LV, Hyp. 880Kv, S9650s w/MG, SK720 w/ DS650. This is the non-stretched Protos flying 425-430mm main blades and stock tail blades.

Note that you will need to adjust the mid, upper, and lower servo travel limits to level the swash since mine won't be exactly the same as yours. I'm also using the Futaba s-bus receiver with my 8FG tx. So you'll have to change this setting as well to your RX. And I have self-leveling on at 90% on bank #2 with tail gains adjustable in the TX in both banks. I have 40% overall tail gain and that is working good for me with the ball at 10.5mm on the tail servo horn.

Don't forget to rename the extension on the file to .SK7.

[Silverexpress01]

Originally Posted by Silverexpress01

being updated

Coaxial setup example:
To be added..




Default values:
For reference...see attached

So I never got around to providing a Co-axial setup. Simply because it's so easy to setup Self-Leveling with SK-720. Also as I've learned all heli's are different, and so a fixed set of numbers can be a crapshoot in applying to all. In order to redeem my promise...try this...

https://www.helifreak.com/showpost.p...6&postcount=38 and once I figure out how to set it up for self-leveling...you shall have that too and some cake.

Update: I figured it out!

[CHIEF-X]

i would like a setup file for a trex450 sev2 with airtronics 94809 servos on cyclic and ino lab hgd-210hb on the tail. and would also know how easy i can make it fly for a newb. i can fly a 4g6s fine in fast foreward flight.

[Lorenzo]

cannot open file; can you do a pdf

[mudfish911]

Does anyone have a setup file for Trex 550e, using the standard align servos as supplied in the combo?

[Wishmaster83]

Does someone have a setup file for a T-Rex 450 Sport withan RJX head and the stock servos (DS410)?
And maybe also a tipp on where to place the SK720 with a Spektrum AR6100 reciever already installed in it?

Greets
Wishmaster83

[CHIEF-X]

dang this thread has grandma'ed lol at least i know i will post my sk720 files when i get the unit flying great. it will be on a outrage fusion 50 running yge 90hv esc, xera 4025 560kv 3y motor torq servos all the way around and a western robotics herculese super bec.see y guyz in a while!! hell ill still prolly be the next post up lol

[georgi UK]

=] yes we can go over the setup log for you, just say how you want it to fly mild or wild!!