Register Now

garfield2412 · 04-01-2013, 04:33 AM

Hi Folks,

I installed this nice 7025LMT in my new 800 Suzi Laos.
Setup is 12s ->BEC ->8.4V, RJX HV Servos (0.05ms, 21kg) - known as moderate amp drawing.
I played a little bit on the work bench and noticed voltages from 8.5V to 7.4V in my V-Bar.
There was no Stress on the Servos or bent Rods!

Is the Voltage drop in a normal Range?
Is it better to switch to the 7.4V Setting?

Thanks for your advises

helicraze · 04-01-2013, 04:46 AM

I would set to 7.4v, i do this with kosmik and hv servo. Those servos are high amp draw setting to 8.4v makes it worse! Set to 7.4

garfield2412 · 04-01-2013, 12:13 PM

Thanks for the advise.
I'll try 7.4v and report.

lezbone · 04-08-2013, 11:18 PM

Are you guys running 12s right into the Gryphon or just wiring it to one 6s pack?

helicraze · 04-09-2013, 04:56 AM

Im running straight 16S on mine

lezbone · 04-09-2013, 08:58 AM

Wow! Do you guys know if the advertised constant and peak amps are applicable at all voltage input ranges? I ask this because many BECs quote available amps based on input voltage, with the best performance being on lower input voltages.

helicraze · 04-09-2013, 03:42 PM

Only ever heard of cc doing that. I use it

04-01-2013, 04:33 AM	#1 (permalink)
garfield2412 Registered Users My HF Map location Join Date: May 2010	Voltage Drop @8.4V - how much? (7025LMT) Hi Folks, I installed this nice 7025LMT in my new 800 Suzi Laos. Setup is 12s ->BEC ->8.4V, RJX HV Servos (0.05ms, 21kg) - known as moderate amp drawing. I played a little bit on the work bench and noticed voltages from 8.5V to 7.4V in my V-Bar. There was no Stress on the Servos or bent Rods! Is the Voltage drop in a normal Range? Is it better to switch to the 7.4V Setting? Thanks for your advises __________________ Velos 880, 800e Pro DFC, Mostro 700, Suzi Laos 800 RJX Xtreme 90EP, Outrage F50, Goblin 570KSE, Goblin 380

04-01-2013, 04:46 AM	#2 (permalink)
helicraze Registered Users Join Date: Apr 2008	Voltage Drop @8.4V - how much? (7025LMT) I would set to 7.4v, i do this with kosmik and hv servo. Those servos are high amp draw setting to 8.4v makes it worse! Set to 7.4

04-01-2013, 12:13 PM	#3 (permalink)
garfield2412 Registered Users Thread Starter My HF Map location Join Date: May 2010	Thanks for the advise. I'll try 7.4v and report. __________________ Velos 880, 800e Pro DFC, Mostro 700, Suzi Laos 800 RJX Xtreme 90EP, Outrage F50, Goblin 570KSE, Goblin 380

04-09-2013, 03:42 PM	#7 (permalink)
helicraze Registered Users Join Date: Apr 2008	Voltage Drop @8.4V - how much? (7025LMT) Only ever heard of cc doing that. I use it

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-08-2013, 11:18 PM	#4 (permalink)
lezbone Registered Users My HF Map location Join Date: Dec 2009 Location: Snoqualmie	Are you guys running 12s right into the Gryphon or just wiring it to one 6s pack?

04-09-2013, 04:56 AM	#5 (permalink)
helicraze Registered Users Join Date: Apr 2008	Im running straight 16S on mine

04-09-2013, 08:58 AM	#6 (permalink)
lezbone Registered Users My HF Map location Join Date: Dec 2009 Location: Snoqualmie	Wow! Do you guys know if the advertised constant and peak amps are applicable at all voltage input ranges? I ask this because many BECs quote available amps based on input voltage, with the best performance being on lower input voltages.

Register Now

Log-in