Register Now

Finless · 06-27-2006, 09:27 PM

The Trewx 600 Build videos will be listed here.

NEW 01/20/2007 Shaft Drive Kit Overview.
This is not a video showing complete assembly but is an over of the system. Installation should be the same as belt drive and should be EASY following my build videos below as it is like the belt drive and tail assemblies
Trex600 Shaft Drive Overview (55 Megs)

The regular build vids are below

Check out the announcement video here:
Trex 600 announcement video

First up:

Kit Contents Overview
What's in the box!! (18 Megs)

VIDEO -> Steps 1 and 2 - Blade grips and head (18 Megs)

NOTE! The flybar supplied is now 440mm instead of 400mm as used in my video. Please be aware of this for the measurements I give for paddle distance!
VIDEO -> Step 3 - Seesaw and flybar (50 Megs)

VIDEO -> Steps 4, 5 & 6 - Head, washout, and swash plate (20 Megs)

VIDEO -> Steps 7 & 8 - Main gear and frames (25 Megs)

VIDEO -> Step 9 - Tail Drive Assembly (10 Megs)

VIDEO -> Steps 10 & 11 - Trays, Motor mount, and Control arms (20 Megs)

VIDEO -> Steps 12 - Landing Gear (9 Megs)

OK folks. At this point for ease of video purposes I am skipping steps 13 through 16 (tail and tail rotor) and going to 17 servo install and head set up. I will return to these steps near the end.

VIDEO -> Servo Install and linkage setup (44 Megs)

VIDEO -> Head and link setup (30 Megs)

VIDEO -> Installing the motor and setting the pinion (15 Megs)

VIDEO -> Installing the electronics (38 Megs)

OK I will now be going back to page 13 and doing the tail of the heli and this will include setting up the servo.

VIDEO -> Tail boom, tail case, and tail shaft (30 Megs)

VIDEO -> Tail pitch slider and tail hub (22 Megs)

VIDEO -> Boom supports and fins (22 Megs)

VIDEO -> Tail servo and gyro setup (35 Megs)

OK basically that is it! I hope you all enjoy the build vids and please feel free to give feedback!
The below vid is just some final comments nothing big. I moved the ESC to the other side of the heli due to the antenna routing as I did this build without the skids on and after placing the skids I realized it was not good to have the ESC close to the antenna.

VIDEO -> Final comments (6 Megs)

VIDEO -> How to mount the flight power 4900 to the Trex600 (19 Megs)

Well I hope you all enjoyed this as much as I did doing the vids!

Enjoy,
Bob

supertrex2 · 06-27-2006, 11:12 PM

damm bob ur fast! lol

Greybird · 06-28-2006, 07:57 PM

Finless. How the heck many heli's do you own?

magicmalik19 · 06-28-2006, 08:35 PM

when will the rest of the build videos be out?

Finless · 06-28-2006, 08:36 PM

I start working on them tomorrow so stay tuned please.
Bob

Stealthpilot · 06-28-2006, 09:49 PM

I dident see any main rotor blades in the box?? Did it not come with any??

Finless · 06-28-2006, 10:22 PM

No the kit does NOT come with blades and I am told Align will not be making blades.

Bob

king kong · 06-28-2006, 11:12 PM

Come on bob, aren't you done yet? Mine's ready for flight at first light. oh, btw can i borrow some servo tape. i'm all out

Finless · 06-28-2006, 11:20 PM

Frank... seeing how you have built in the past I am sure it is sloppy.... You want to get in the air fast and dont care about a QUALITY build.... Seen your work before...

If you lockout this weekend I will be sure to have my camera!

I bet I will not approve of your wiring job, etc but we shall see...

One day when you grow out of puberty you will appreciate spending time building a GOOD heli...

Of course I am picking on you ya know

Bob

good2win22 · 06-28-2006, 11:36 PM

Hey Bob,

Don't know what you did different, but the image quality is greatly improved. Keep up the great work. I look forward to seeing your builds.

Jason

mountaindr3wz · 06-28-2006, 11:55 PM

looks like you got a new camera bob. i see the jvc remote control in your hand.

Finless · 06-28-2006, 11:59 PM

Same camera I have always used.......

Bob

audiosong · 06-29-2006, 10:08 AM

Hi, good job, thanks for this first video. :mrgreen:

magicmalik19 · 06-29-2006, 10:58 PM

are the video's still being posted here?

Finless · 06-29-2006, 11:29 PM

Yes the build videos WILL be here. I am sorry that I could not get started TODAY as I said but for sure the 600 build vids will start tomorrow! Realize I have a day job like many and I was working on vids before th 600 came in.

Sorry all for the delay but do not worry... They will start showing up SOON!

Bob

magicmalik19 · 06-29-2006, 11:51 PM

ok thanks, and dont worry about explaining ur busy. Im gonna put mine together tonight.

Raven_darkcloud · 06-30-2006, 01:16 AM

Hay bob just how do you bankroll all this? lol. 2 new heli's in one week wow. Wish my paychecks could do that. I know they are vastly diferent in size but can you do a comparasin betwean the 600 and the lepton when they are done?

Finless · 06-30-2006, 10:19 AM

Quote:

Originally Posted by Raven_darkcloud

Hay bob just how do you bankroll all this? lol. 2 new heli's in one week wow. Wish my paychecks could do that. I know they are vastly diferent in size but can you do a comparasin betwean the 600 and the lepton when they are done?

I sure can! I will start shooting the Trex600 today for sure. The Lepton will be done today as well.

Bob

supertrex2 · 06-30-2006, 07:02 PM

Does that mean you will start some Trex600 vids today also?

Finless · 06-30-2006, 08:57 PM

Yep I just posted the first steps!
Steps 1 and 2

Bob

06-27-2006, 09:27 PM	#1 (permalink)
Finless Team Taco VP My HF Map location Join Date: Nov 2005	Trex 600E Build Videos will be here: The Trewx 600 Build videos will be listed here. NEW 01/20/2007 Shaft Drive Kit Overview. This is not a video showing complete assembly but is an over of the system. Installation should be the same as belt drive and should be EASY following my build videos below as it is like the belt drive and tail assemblies Trex600 Shaft Drive Overview (55 Megs) The regular build vids are below Check out the announcement video here: Trex 600 announcement video First up: Kit Contents Overview What's in the box!! (18 Megs) VIDEO -> Steps 1 and 2 - Blade grips and head (18 Megs) NOTE! The flybar supplied is now 440mm instead of 400mm as used in my video. Please be aware of this for the measurements I give for paddle distance! VIDEO -> Step 3 - Seesaw and flybar (50 Megs) VIDEO -> Steps 4, 5 & 6 - Head, washout, and swash plate (20 Megs) VIDEO -> Steps 7 & 8 - Main gear and frames (25 Megs) VIDEO -> Step 9 - Tail Drive Assembly (10 Megs) VIDEO -> Steps 10 & 11 - Trays, Motor mount, and Control arms (20 Megs) VIDEO -> Steps 12 - Landing Gear (9 Megs) OK folks. At this point for ease of video purposes I am skipping steps 13 through 16 (tail and tail rotor) and going to 17 servo install and head set up. I will return to these steps near the end. VIDEO -> Servo Install and linkage setup (44 Megs) VIDEO -> Head and link setup (30 Megs) VIDEO -> Installing the motor and setting the pinion (15 Megs) VIDEO -> Installing the electronics (38 Megs) OK I will now be going back to page 13 and doing the tail of the heli and this will include setting up the servo. VIDEO -> Tail boom, tail case, and tail shaft (30 Megs) VIDEO -> Tail pitch slider and tail hub (22 Megs) VIDEO -> Boom supports and fins (22 Megs) VIDEO -> Tail servo and gyro setup (35 Megs) OK basically that is it! I hope you all enjoy the build vids and please feel free to give feedback! The below vid is just some final comments nothing big. I moved the ESC to the other side of the heli due to the antenna routing as I did this build without the skids on and after placing the skids I realized it was not good to have the ESC close to the antenna. VIDEO -> Final comments (6 Megs) VIDEO -> How to mount the flight power 4900 to the Trex600 (19 Megs) Well I hope you all enjoyed this as much as I did doing the vids! Enjoy, Bob __________________ "Don't Taco My Pack Dude!" NEW Video Link -> Safety Video #1 Video Link -> CAUTION using powerful tools! Video Link -> How to CRASH TWICE in one flight! Video Link -> Don't Taco! Last edited by HF_Jason; 01-23-2020 at 08:47 AM.. Reason: title change

06-27-2006, 11:12 PM	#2 (permalink)
supertrex2 Registered Users Join Date: May 2006	damm bob ur fast! lol __________________ oh ohh its going down...S$%#T...relax.. relax.... concentrate......try to control.. oooops too late... already crashed!

06-28-2006, 08:35 PM	#4 (permalink)
magicmalik19 Registered Users Join Date: Dec 2004	when will the rest of the build videos be out? __________________ http://www.facebook.com/group.php?gid=2205103463#!/profile.php?id=8826230

06-28-2006, 08:36 PM	#5 (permalink)
Finless Team Taco VP Thread Starter My HF Map location Join Date: Nov 2005	I start working on them tomorrow so stay tuned please. Bob __________________ "Don't Taco My Pack Dude!" NEW Video Link -> Safety Video #1 Video Link -> CAUTION using powerful tools! Video Link -> How to CRASH TWICE in one flight! Video Link -> Don't Taco!

06-28-2006, 09:49 PM	#6 (permalink)
Stealthpilot Registered Users Join Date: May 2006	I dident see any main rotor blades in the box?? Did it not come with any?? __________________ Randy TRex 600 Nitro Pro, TRex 450 pro Boeing CH-47F NETT SI

06-28-2006, 07:57 PM	#3 (permalink)
Greybird Registered Users Join Date: May 2006	Finless. How the heck many heli's do you own?

06-28-2006, 10:22 PM	#7 (permalink)
Finless Team Taco VP Thread Starter My HF Map location Join Date: Nov 2005	No the kit does NOT come with blades and I am told Align will not be making blades. Bob __________________ "Don't Taco My Pack Dude!" NEW Video Link -> Safety Video #1 Video Link -> CAUTION using powerful tools! Video Link -> How to CRASH TWICE in one flight! Video Link -> Don't Taco!

06-28-2006, 11:12 PM	#8 (permalink)
king kong Registered Users Join Date: May 2006	Come on bob, aren't you done yet? Mine's ready for flight at first light. oh, btw can i borrow some servo tape. i'm all out __________________ Make it go BOOM Team Flightpower

06-28-2006, 11:20 PM	#9 (permalink)
Finless Team Taco VP Thread Starter My HF Map location Join Date: Nov 2005	Frank... seeing how you have built in the past I am sure it is sloppy.... You want to get in the air fast and dont care about a QUALITY build.... Seen your work before... If you lockout this weekend I will be sure to have my camera! I bet I will not approve of your wiring job, etc but we shall see... One day when you grow out of puberty you will appreciate spending time building a GOOD heli... Of course I am picking on you ya know Bob __________________ "Don't Taco My Pack Dude!" NEW Video Link -> Safety Video #1 Video Link -> CAUTION using powerful tools! Video Link -> How to CRASH TWICE in one flight! Video Link -> Don't Taco!

06-28-2006, 11:36 PM	#10 (permalink)
good2win22 Registered Users My HF Map location Join Date: May 2006	Hey Bob, Don't know what you did different, but the image quality is greatly improved. Keep up the great work. I look forward to seeing your builds. Jason __________________ Raptor 50 Titan Trex 700

06-28-2006, 11:55 PM	#11 (permalink)
mountaindr3wz Registered Users Join Date: May 2006	looks like you got a new camera bob. i see the jvc remote control in your hand.

06-28-2006, 11:59 PM	#12 (permalink)
Finless Team Taco VP Thread Starter My HF Map location Join Date: Nov 2005	Same camera I have always used....... Bob __________________ "Don't Taco My Pack Dude!" NEW Video Link -> Safety Video #1 Video Link -> CAUTION using powerful tools! Video Link -> How to CRASH TWICE in one flight! Video Link -> Don't Taco!

06-29-2006, 10:08 AM	#13 (permalink)
audiosong Join Date: Mar 2006	Hi, good job, thanks for this first video. :mrgreen:

06-29-2006, 10:58 PM	#14 (permalink)
magicmalik19 Registered Users Join Date: Dec 2004	are the video's still being posted here? __________________ http://www.facebook.com/group.php?gid=2205103463#!/profile.php?id=8826230

06-29-2006, 11:29 PM	#15 (permalink)
Finless Team Taco VP Thread Starter My HF Map location Join Date: Nov 2005	Yes the build videos WILL be here. I am sorry that I could not get started TODAY as I said but for sure the 600 build vids will start tomorrow! Realize I have a day job like many and I was working on vids before th 600 came in. Sorry all for the delay but do not worry... They will start showing up SOON! Bob __________________ "Don't Taco My Pack Dude!" NEW Video Link -> Safety Video #1 Video Link -> CAUTION using powerful tools! Video Link -> How to CRASH TWICE in one flight! Video Link -> Don't Taco!

06-29-2006, 11:51 PM	#16 (permalink)
magicmalik19 Registered Users Join Date: Dec 2004	ok thanks, and dont worry about explaining ur busy. Im gonna put mine together tonight. __________________ http://www.facebook.com/group.php?gid=2205103463#!/profile.php?id=8826230

06-30-2006, 01:16 AM	#17 (permalink)
Raven_darkcloud Registered Users My HF Map location Join Date: Mar 2006	Hay bob just how do you bankroll all this? lol. 2 new heli's in one week wow. Wish my paychecks could do that. I know they are vastly diferent in size but can you do a comparasin betwean the 600 and the lepton when they are done? __________________ Team Outrage OPM - Fly it like it aint yours! JR X9303 2.4 Baby. I have felt the difference and I like it! Don"t make me list 'm all !

06-30-2006, 07:02 PM	#19 (permalink)
supertrex2 Registered Users Join Date: May 2006	Does that mean you will start some Trex600 vids today also? __________________ oh ohh its going down...S$%#T...relax.. relax.... concentrate......try to control.. oooops too late... already crashed!

06-30-2006, 08:57 PM	#20 (permalink)
Finless Team Taco VP Thread Starter My HF Map location Join Date: Nov 2005	Yep I just posted the first steps! Steps 1 and 2 Bob __________________ "Don't Taco My Pack Dude!" NEW Video Link -> Safety Video #1 Video Link -> CAUTION using powerful tools! Video Link -> How to CRASH TWICE in one flight! Video Link -> Don't Taco!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in