START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Futaba 14MZ - 12Z Futaba 14MZ and 12Z Help and features Support Forum |
|
LinkBack | Thread Tools | Display Modes |
01-04-2012, 06:17 PM | #1 (permalink) |
Registered Users
Join Date: Apr 2010
|
Spektrum module
I know, i know. Shouldn't be thinking this, however i have lots of cheap BNF's and would like to still fly them without putting expensive futaba rx's in.
Which is the correct spek module for the 14mz?? Cheers.
__________________
Oxy 3 SK540 Minijazz 20 / WARP 360 SK540 Koby 55 / Goblin 500 SK540 jive 100 / 6HV ultimate Helijive120 SK540 / 7HV SK540 Kosmik200 / Futaba18mz / Skookum support rep |
Sponsored Links | |||
Advertisement |
|
01-05-2012, 01:35 AM | #2 (permalink) |
Registered Users
|
Maybe ask this in the Spektrum forum area? I am not even sure they still make the module, I could be wrong on that. It attaches to the back of the TX and takes a PPM feed off the trainer plug.
__________________
Team Futaba - Kontronik Futaba 32MZ/18MZ/18SZ/16SZ - CGY760 and 755 |
01-05-2012, 04:01 AM | #3 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2010
|
A few guys at my club are using 1 with 10c's. Will phone the distributor
__________________
Oxy 3 SK540 Minijazz 20 / WARP 360 SK540 Koby 55 / Goblin 500 SK540 jive 100 / 6HV ultimate Helijive120 SK540 / 7HV SK540 Kosmik200 / Futaba18mz / Skookum support rep |
01-05-2012, 08:08 AM | #4 (permalink) |
Registered Users
Join Date: Aug 2006
|
Most are actually picking up a used DX6 somewhere to use with the BNF stuff. Cheaper than the module.
__________________
Team Synergy/Rail Blades, Team Scorpion, VelTye, YS Engines, JAG-RC, Electron Retracts |
01-05-2012, 10:46 AM | #5 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2010
|
Might just keep the dx7 for this then, can't be bothered with the extra hassle.
__________________
Oxy 3 SK540 Minijazz 20 / WARP 360 SK540 Koby 55 / Goblin 500 SK540 jive 100 / 6HV ultimate Helijive120 SK540 / 7HV SK540 Kosmik200 / Futaba18mz / Skookum support rep |
01-18-2012, 12:19 AM | #6 (permalink) |
Registered Users
|
Agree with kcordell that DX6i could be a better choice.
But if you really want the module, here it is: http://www.spektrumrc.com/Products/D...rodId=SPMMSMZ7 I have one and it works great. You can find used one for less than $50 on various RC forums. |
01-15-2013, 06:50 PM | #8 (permalink) |
Registered Users
Join Date: Aug 2011
|
Spektrum module
My 14MZ has a spectrum modual Taft plus into the training port. But it's to complicated for me to use
Beep, Beep, Honk, Honk, Over and Out Rotorhead
__________________
Any Landing you can walk away from, is a good landing... |
03-24-2013, 01:07 PM | #9 (permalink) |
Registered Users
|
this is probably the best and easiest spektrum module out
http://www.rcgroups.com/forums/showt...modul+aurora+9 works with any radio via trainer port of the rf module port of the radio you can pick the transmitter brand and it will remap the channels to spektrum standards. Which has always been the pain with use a spektrum module. and it is both dsm-2 and dsm-x. Unlike most that are dsm-2 only
__________________
4 x Rush 750/stretched V-bar KDE 700XF-495 HV servos Greys reactor CC 160-HV Trex 600EFL V2 V-Bar ds610 ds650 CC bec/pro Scorpion 130a HV KDE 600XF-530 450L KDE 1750 cc50 4xDS215MG k-bar X-8 FPV Wing, TBS Discovery FPV, TBS Caipirinha FPV |
Thread Tools | |
Display Modes | |
|
|