START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Hurricane 425 Discussion and support of the Gaui Hurricane 425 |
|
LinkBack | Thread Tools | Display Modes |
06-09-2010, 04:33 PM | #1 (permalink) |
Registered Users
|
Power systems that work
425 Power Systems that WORK!!
post em up boys.
__________________
Gaui 200 •Gaui 550 •Gaui X5 BeastX Castle Scorpion Hyperion Spektrum JR The Front Porch, Nexgens Lounge |
Sponsored Links | |||
Advertisement |
|
06-12-2010, 02:53 AM | #2 (permalink) |
Registered Users
Join Date: Sep 2007
|
I'm running a
1600 kv mystery motor (started with a stock trex 1600kv motor, but switched it out for one that fit under the canopy). Align RCE-BL6DG esc Turnigy 6s 2200 13t pinion, 50t front & 61t main gear, stock one way gear (20t) 430mm wide chord Mavrikk blades. 5 minute 30 sec flight time, flying beginner 3d & FFF. Charge will replace on average 1500mah. So far batt, motor & esc temps have not topped 100 degree range, we will see what happens as the summer heats up. |
06-20-2010, 01:57 PM | #3 (permalink) |
Registered Users
Join Date: Jun 2008
|
Scorpion HK3026-1600kv
14t Pinion Castle ICE 100 Hyperion G3 VX 2600mah 6s running about 80% throttle and it is crazy powerful, I love it
__________________
Forza 450 |
06-22-2010, 09:28 PM | #4 (permalink) |
Registered Users
Join Date: May 2010
|
Scorpion 3026-1210 ICE 75. 2x 3S 2650 25C zippy
15t pinion, 50t main gear, 20t one way bearing.
__________________
Gaui X7 MSH Brain YGE160HV Xera4035-480 Gaui X475 FES MSH Brain YGE120 Xera4020 Gaui X5 MSH Brain YGE90HV Xera 4025 Gaui X6 vbar silver 5.3 YGE120HV 700mx Last edited by joe1l; 07-07-2010 at 07:55 PM.. |
06-27-2010, 09:24 AM | #5 (permalink) |
Registered Users
Join Date: Oct 2009
|
Stock gearing with 14t pinion, scorpion 3026-1400kv, cc ice 100, spartan quark/jr 810g, 6c 3000mah zippy, align cf blades.
|
07-07-2010, 07:57 PM | #6 (permalink) |
Registered Users
Join Date: May 2010
|
Anybody shopping a power setup, take a look at this calculator by castle. Had I seen it before i setup my my motor i would of saved myself a crash! Be very careful with the Scorpion 3026-1400...it runs pretty hot and likes to turn off on hot days!!
__________________
Gaui X7 MSH Brain YGE160HV Xera4035-480 Gaui X475 FES MSH Brain YGE120 Xera4020 Gaui X5 MSH Brain YGE90HV Xera 4025 Gaui X6 vbar silver 5.3 YGE120HV 700mx |
09-21-2010, 04:54 PM | #7 (permalink) |
Registered Users
|
I'm running a Hacker A40 1600kv with a Castle Phoenix 60 on 13/60/20/61, works out pretty good for fast sport flying. I get about 4:30-5:00 with 2650mah, everything comes down warm to the touch.
|
10-21-2010, 03:35 PM | #8 (permalink) |
Registered Users
Join Date: Dec 2007
|
Z20A 1700Kv, CC Ice Lite 75, Gear 13/60/19/61, 6s 2650mAh, Idle1 1900Rpm, Idle2 2300Rpm
__________________
Hub Flo Hurricane 425, Z20A 1700KV,CC ICE Lite 75,BeastX,S9650, 3xS3152,AR6200 Spektrum DX6i |
10-23-2010, 06:46 PM | #9 (permalink) |
Registered Users
Join Date: Oct 2008
Location: Italy
|
ESc: Align 60A (the one from Trex 500)
Motor: Turnigy H3126/1300Kv Pinion 14T (all the rest stock). 5:30 min with Zippy Flightmax 2200/25C / 3S x2 in series it's Good! |
11-01-2010, 08:25 PM | #10 (permalink) |
Registered Users
Join Date: Aug 2007
Location: Georgia
|
How is that motor working out for you ?
__________________
RAW 580 ,lots of Planes Powered by IX14 AMA 36 yrs. |
01-02-2011, 03:33 PM | #11 (permalink) |
Registered Users
Join Date: Feb 2010
|
Hi,
Motor: Align 500M / 1600kv ESC: Turnigy Brushless ESC 85A w/ 5A SBEC ( a very good governor function and soft start in gov mode ) BEC: Turnigy 8-15A with Turnigy 2s / 800mah Pinions : 14 / 60 / 19 / 61 7 min. with Turnigy 6s / 3000mah Very Powerful setup with 86% in TX ( Headspeed 2600rpm ) Regards Marc |
02-07-2011, 11:47 AM | #12 (permalink) |
Registered Users
|
Scorpion 3026-1600kv (6-pole, 8kHz PWM)
Phoenix ICE 100 (Set RPM mode at 2600, normal motor advance) Turnigy 6s 2200 40C 15t pinion and stock gears (61T rear main, 19T one-way, 50T front main) Stock plastic kit, no upgrades 430mm wide chord Mavrikk (Red) blade, sometimes the Align blades Pitch +/- 10 degrees Cyclic +/- 8 degrees 5 minute flight time, moderate 3D (loops, rolls, flips) & hard FFF (hard turns, stall turns, Immelman's, S-turns). I started as a plane pilot Winter flying (32F - 50F): Motor temp ~97F, battery temp ~98F. I used to run the above setup with the Scorpion 3026-1400kv (10-pole, 8kHz PWM) but motor temps were ~130F and battery ~115F even on low motor advance. And, the motor was hitting 100% output on moderate to heavy maneuvers. Fortunately, these motors are rated to 356F. Switching ot 1600kv brought all temps down and it rarely hits 100% output. Last edited by Dracx; 02-10-2011 at 11:40 AM.. |
03-24-2011, 09:38 AM | #13 (permalink) |
Registered Users
Join Date: Feb 2009
|
I'm using this motor, with stock gearing. and 14t pinion
http://www.hobbyking.com/hobbyking/s...idProduct=7243 a ice 75, and a dimention engineering sport bec, and a zippy 2650 40c battery. waiting on parts to get it back in the air. had a CC standard bec, but somehow it fried and took out my bls251 tail servo.. I hope.. I hope it didnt toast the rest of the gy611 gyro setup.. I dont have money to replace the rest of that. |
04-17-2011, 01:46 PM | #14 (permalink) | |
Registered Users
|
Quote:
|
|
05-11-2011, 04:30 AM | #15 (permalink) |
Registered Users
Join Date: Sep 2010
|
heres mine , inever got around to it
gaui scorpion 504 (3026-1400kv)1680 watts cc ice 75 stock gears except 20t one way, 15t pinion stock 425 blades +/- 13 degress pitch 10 cyclic fbl sk720 xf frame full size servos flight time 5 min on sport 4:30 moderate 3d 4 min hard 3d motor does get hot, but not above 110 esc is hot but not bad, hyperion packs 2950 35c cool, maybeewarm , but barley |
07-23-2011, 02:24 PM | #16 (permalink) |
Registered Users
Join Date: Jul 2011
|
hii i need little help..i have a new huricane ep425 but i cant find good power conversation..
motor : turnigy 1300kv (15t pinion) lipo : turnigy 6s 3000mAh 20c cyclic : futaba s3003 rudder : kds800+ n590 esc : ?? choose 1-) turnigy plush 80a(maybe with turnigy sbec5a) choose 2-) turnigy super brain 80a what should i do? thanks |
Thread Tools | |
Display Modes | |
|
|