Troubleshoot Info in use (solved)

[Grittner]

I just finish installing the kosmik 160, and I turn on and nothing happens, according to the guid, since have no LEDs on is info in use... What does it mean what me I doing rong

[EEngineer]

Can't tell by the limited info you posted.

Please check out the "sticky" on the Kos Upgrade.....works for both the Kos160, as well as the Kos200.

I recommend using a freshly charged main battery pack....to upgrade your Kos160..

FWIW

[Wh1teAfr1can]

Originally Posted by EEngineer

Can't tell by the limited info you posted.

Please check out the "sticky" on the Kos Upgrade.....works for both the Kos160, as well as the Kos200.

I recommend using a freshly charged main battery pack....to upgrade your Kos160..

FWIW

Dont think hes upgrading it he is just installing it. Make sure the wires are plugged in by the Black Red Yellow on the case not by the way the servo plug fits in.

[EEngineer]

I just didn't understand....

But, the labeling on my Kos 200 matches the color coding on my SBEC leads.

As well as the "beveling" on the Kos input receptacle....with respect to the SBEC
input leads(with toroids...lol).

An older unit in his case?....I don't know.

[Grittner]

The unit is brand new V4.4, I plug the motor, new pack charged, master to RX, I bind the Tx but nothing happens..

[taosgraveyard]

Double check all connections,

Battery pack connected correctly?

Can you connect to it with a progdisc?

[Grittner]

sended my progdisc for warranty so don't have it..

Originally Posted by taosgraveyard

Double check all connections,

Battery pack connected correctly?

Can you connect to it with a progdisc?

[Wh1teAfr1can]

Originally Posted by Grittner

sended my progdisc for warranty so don't have it..

are you at zero throttle when booting it up? make sure you have your linear curve 0-100 and be in normal mode stick down and then press the button to enter programming mode.

[Grittner]

Problem solved..
i had everything correct "except" tat i had a CC ESC before and it require to adjust Thruttle travel and it was low point at 23 so the ESC never armed because it did not see a "0"..
i just lower to 0 - 100 and

thank for everyone help.

[kevinbj]

Can someone tell me what both legs blinking red continues on kosmik mean? It usually only does it when I do hurricanes but only pulling 150 amps. It doesn't cut off it lowers the room from 2150 to 1800 then I see both red blinking lights continues. .Both bats are new jus less then month old so not that. Motor is 4525 hand wound mini v-bar futaba bus 255 on 7.4v rail 696

[taosgraveyard]

Logs?

[Wh1teAfr1can]

Originally Posted by kevinbj

Can someone tell me what both legs blinking red continues on kosmik mean? It usually only does it when I do hurricanes but only pulling 150 amps. It doesn't cut off it lowers the room from 2150 to 1800 then I see both red blinking lights continues. .Both bats are new jus less then month old so not that. Motor is 4525 hand wound mini v-bar futaba bus 255 on 7.4v rail 696

there has been an error in use. post or email me the log and i will take a look at it. you should also have an error log.

[kevinbj]

Originally Posted by Wh1teAfr1can

there has been an error in use. post or email me the log and i will take a look at it. you should also have an error log.

can you please send me your email.. I tried for an hour to post log but cant seem to make it work