Register Now

norstaroption · 10-02-2015, 06:15 PM

This is the part I don't get when setting up gov for electric heli. Using CC120HV ESC, do you guys have to mess with the default values on the Throttle Servo Adjustments? Do you guys have to calibrate your ESC?

I'm using NEO Express no vlink and CC120HV.

Thanks in advance.

Kevin Dalrymple · 10-02-2015, 06:59 PM

Yes you will need to adjust the end points for the ESC on Castle Esc's. There is a castle set up video on the Vstabi web site under electric gov. They set up a castle 120.

Larry227 · 10-02-2015, 11:14 PM

Oddly enough I didn't do anything on the Neo for my 700 with an Ice2 120HV. I left it at the default -100/+100 and it works fine.
On my 6HV with Hobbywing 70HV I just input the same values I used on the Blue Vbar (-104/+100) and it works fine.

norstaroption · 10-03-2015, 12:00 AM

What about your sensor configuration? Did you enter half of the motor pole?

I'm not getting the head speed I wanted. It worked fine with my silver line.

Larry227 · 10-03-2015, 06:26 AM

Yes 1/2 the pole count. Using Hobbywing phase sensor on both.

Larry227 · 10-03-2015, 06:26 AM

Did you hit the reset button on the first gov tab when you chose Electric?

norstaroption · 10-03-2015, 09:10 AM

Quote:

Originally Posted by Larry227

Yes 1/2 the pole count. Using Hobbywing phase sensor on both.

I'm using the built in rpm sensor from the CC Edge.

Love_Heli · 10-27-2015, 07:34 AM

I'm using nitro Gov on NEO, but i cannot turning min throtle adjust. Who heve help me !
Thank you

akular1 · 10-27-2015, 07:41 AM

I am also not able to adjust the minimum throttle adjustment. The maximum level works with the fine tune adjustments in the software, but the minimum doesnt move no matter which way we adjust the lever in the software.

Also, what about idle vs throttle cut. Can we set the heli to idle (and adjust the idle as needed) when the throttle stick is ALL the way down?

Andy

Love_Heli · 11-01-2015, 03:53 AM

Hello Andy,
I'm just finish on NX7

. If you want to adjust, please download new PC or Mac software and turn off TX to work fine

akular1 · 11-01-2015, 06:17 PM

Hi there

Thanks for your message! Is there new software that we should download to enable this? Was this a new release. Also, when you indicate turn off transmitter, how can I adjust the trim with the transmitter off. I appreciate your help

Thanks again!
Andy

10-02-2015, 06:15 PM	#1 (permalink)
norstaroption Registered Users Join Date: May 2010	Throttle Servo Adjustment This is the part I don't get when setting up gov for electric heli. Using CC120HV ESC, do you guys have to mess with the default values on the Throttle Servo Adjustments? Do you guys have to calibrate your ESC? I'm using NEO Express no vlink and CC120HV. Thanks in advance. __________________ Protos 380 NEO x2 Oxy 2 Goblin Fireball

10-02-2015, 06:59 PM	#2 (permalink)
Kevin Dalrymple Registered Users Join Date: Jul 2006	Yes you will need to adjust the end points for the ESC on Castle Esc's. There is a castle set up video on the Vstabi web site under electric gov. They set up a castle 120. __________________ Synergy Field Rep Rail Blades Field Rep

10-02-2015, 11:14 PM	#3 (permalink)
Larry227 Registered Users My HF Map location Join Date: Jul 2008	Oddly enough I didn't do anything on the Neo for my 700 with an Ice2 120HV. I left it at the default -100/+100 and it works fine. On my 6HV with Hobbywing 70HV I just input the same values I used on the Blue Vbar (-104/+100) and it works fine. __________________ Trex 700 Pro DFC - Compass 6HV - Vcontrol - Neo #nodroneshere - 104

10-03-2015, 12:00 AM	#4 (permalink)
norstaroption Registered Users Thread Starter Join Date: May 2010	What about your sensor configuration? Did you enter half of the motor pole? I'm not getting the head speed I wanted. It worked fine with my silver line. __________________ Protos 380 NEO x2 Oxy 2 Goblin Fireball

10-03-2015, 06:26 AM	#5 (permalink)
Larry227 Registered Users My HF Map location Join Date: Jul 2008	Yes 1/2 the pole count. Using Hobbywing phase sensor on both. __________________ Trex 700 Pro DFC - Compass 6HV - Vcontrol - Neo #nodroneshere - 104

10-03-2015, 06:26 AM	#6 (permalink)
Larry227 Registered Users My HF Map location Join Date: Jul 2008	Did you hit the reset button on the first gov tab when you chose Electric? __________________ Trex 700 Pro DFC - Compass 6HV - Vcontrol - Neo #nodroneshere - 104

10-27-2015, 07:34 AM	#8 (permalink)
Love_Heli Registered Users Join Date: May 2009	I'm using nitro Gov on NEO, but i cannot turning min throtle adjust. Who heve help me ! Thank you __________________ VŨ NGUYỄN Gaui NX7 OS-105 HZ-R - HATORIES PIPE - MKS950HV - MKS980HV - MIKADO V 5.3 PRO Gaui X7F K160 - SCORPION HK-4530-540KV - MKS950HV - MKS980HV - MIKADO V 5.3 PRO LOGO 690SX JIVE PRO 120HV - MKS665HV - MKS669HV - MIKADO V 5.3 PRO

10-27-2015, 07:41 AM	#9 (permalink)
akular1 Registered Users Join Date: Dec 2005	I also am having this issue with the nitro governor I am also not able to adjust the minimum throttle adjustment. The maximum level works with the fine tune adjustments in the software, but the minimum doesnt move no matter which way we adjust the lever in the software. Also, what about idle vs throttle cut. Can we set the heli to idle (and adjust the idle as needed) when the throttle stick is ALL the way down? Andy

11-01-2015, 03:53 AM	#10 (permalink)
Love_Heli Registered Users Join Date: May 2009	Hello Andy, I'm just finish on NX7 . If you want to adjust, please download new PC or Mac software and turn off TX to work fine __________________ VŨ NGUYỄN Gaui NX7 OS-105 HZ-R - HATORIES PIPE - MKS950HV - MKS980HV - MIKADO V 5.3 PRO Gaui X7F K160 - SCORPION HK-4530-540KV - MKS950HV - MKS980HV - MIKADO V 5.3 PRO LOGO 690SX JIVE PRO 120HV - MKS665HV - MKS669HV - MIKADO V 5.3 PRO

11-01-2015, 06:17 PM	#11 (permalink)
akular1 Registered Users Join Date: Dec 2005	follow up Hi there Thanks for your message! Is there new software that we should download to enable this? Was this a new release. Also, when you indicate turn off transmitter, how can I adjust the trim with the transmitter off. I appreciate your help Thanks again! Andy

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in